manualshive.com logo in svg

FOR-A USF-101MDX4-12G, Operation Manual

Share
Download
FOR-A USF-101MDX4-12G Operation Manual Download Page 27

27 

4-3. Event Tab 

Selecting the 

Event

 tab shows the following screen. 

 

 

Item 

Default 

Setting 

Description 

Startup Event 

Last 
Settings 

Last Settings 
Default 
Event 1-100 

Selects an event number to be loaded when 
the unit power turns on. 

Last Settings

: Loads the settings last used. 

Default

: Resets all settings to default at 

startup. 

Event1-100

: Loads the selected event 

memory at startup. 

Load Event button 

－

 

－

 

Pressing the button loads the event selected 
below under 

Event No.

 

Save Event button 

－

 

－

 

Pressing the button saves settings to the 
event selected below under 

Event No.

 

 

IMPORTANT 

Turn off the power supply 5 seconds after event saving. If the power supply is turned off less than 
5 seconds after saving, the event may not be properly saved. 

 
 

4-4. Status Tab 

Selecting  the 

Status

  tab  shows  the  following  screen,  in  which  Serial  Number,  MAC  address, 

Version Information and Option status of the module are displayed. 
 

 

 
 

Summary of Contents for USF-101MDX4-12G

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands