FOR-A USF-101MDX4-12G Operation Manual Download

Page: 22 / 48

Item

Default

Setting

Description

Embedded
Ch.1-16
AES
Ch.1-8

Ch.1-16

Source
Ch.1-16

Source Ch. 1-16
500Hz Tone
1kHz Tone
Silence
Down Mix L
Down Mix R
Mono Sum
Ch. 1-8

Selects an audio source for each channel.

Source Ch. 1-16

: Audio signals embedded in

SDI inputs.

1kHz, 500Hz Tone

: Test signals

Silence

: Mute signal

Downmix L/R

: Downmixed audio channels

Mono Sum Ch1-8

: Mono-summed audio

channels.

USF-101MDX4-12G
If Ch1/2-3/4 or Ch5/6-7/8 terminals are set to

Input

under AES Input Settings in

Sec. 4-2-2.

“AES Input”, audio output channel source is not selectable.

USF-101MDX8-12G
If Ch1/2-3/4 to Ch13/14-15/16 terminals are set to

Input

under AES Input Settings in

Sec. 4-2-2.

“AES Input”, audio output channel source is not selectable.

4-2-7. Monosum / Downmix / Test Signal

Selecting

Monosum Downmix Test Signal

in the Audio Block diagram opens the following

menu screen.
<If

Downmix

is selected>

Item

Default

Setting

Description

Downmix
Mode

Stereo

Stereo
Surround
Monaural

Selects the Downmix mode.

Mix Level
Surround

-3dB

-3dB
-6dB
-9dB
Off

Sets the Ls/Rs (Surround channels) level.
Setting to

Off

removes the Ls/Rs channels from

mixing sources.

Mix Level
Center

-3dB

-3dB
-4.5 dB
-6dB

Sets the C (Center channel) level.
To use the same level as audio sources, set to

-3dB.

The L/R channel volume of downmixed audio may
sound too large. In such cases, decrease the Center
level to

-4.5dB

-6dB

Mix Level
Master

-3dB

-3dB
0dB
Auto

Sets the entire downmix audio level.
If set to

Auto

, Mix Level - Master changes according

Downmix Mode

and

Mix Level - Surround

settings.

Mix Source Assign

Left

Source Ch.1

Source Ch.1-16
500Hz Tone
1kHz Tone
Silence

Selects an audio source
for the selected channel.

Right

Source Ch.2

Center

Source Ch.3

Left Surround

Source Ch.5

Right Surround Source Ch.6

Summary of Contents for USF-101MDX4-12G

















































Search results

Summary of Contents for USF-101MDX4-12G

Reviews:

Related manuals for USF-101MDX4-12G

Brands by name

Popular brands

FOR-A USF-101MDX4-12G, Operation Manual

Search results

Summary of Contents for USF-101MDX4-12G

Reviews:

Related manuals for USF-101MDX4-12G

Brands by name

Popular brands