background image

INSTRUCTIONS FOR USE

ON AND OFF

Before switching on the power supply check that the volume controls of channels 1 to 4 are at their minimum.
Switch on the rest of the audio system and finally switch on the amplifier and adjust the volume controls.

To switch off the audio system adjust the amplifier’s volume to the minimum and switch it off.Finally switch
off the rest of the audio system.

PROTECTION

The amplifier has 4 types of protection: overload, overcurrent, surge and temperature.

When protection is activated, an LED indicator lights up in the front panel and cuts off the audio output. In
this case, check what has caused the activation of the protection, leave it to recover for a few moments  and
then switch it back on.

RESETTABLE FUSE

The power supply source is manufactured with advanced components which absorb current peaks and
eliminate fluctuations caused by switching the amplifier on. Furthermore, the amplifier is equipped with a 10
A BREAKER resettable fuse located in the rear panel.

If the fuse is cut off, due to a surge or excessive consumption, switch the power amp off, check what has
caused the fuse to be cut off, let it recover for a few moments  and reset the fuse BREAKER by pressing it.

TECHNICAL SPECIFICATIONS

FS-4256E

CHARACTERISTICS

4-channel power amplifier.

POWER

Stereo and parallel mode: 4 x 250 W RMS
Bridge mode: 2 x 500 W RMS at 8 Ω 

RESPONSE

30-20,000 Hz, ±3 dB

DISTORTION

Harmonic: < 1%

INPUTS

4 balanced aux lines, XLR, 700 mV RMS

OUTPUTS

4 balanced aux lines, XLR

FUNCTIONS

Ventilation with speed variable with temperature
LED power, signal, clip, temperature and protection indicators

CONTROLS

Volume per channel
GND lift earth disconnection
Parallel/stereo/bridge operating mode selector

PROTECTION

Overload, overcurrent, surge and temperature

S/N RATIO

> 90 dB

IMPEDANCE

4 and 8 Ω and 100 and 70 V lines, screw terminals

POWER SUPPLY

230/115 V AC, 1,800 W maximum
Resettable 10 A fuse

DIMENSIONS

483 x 133 x 460 mm depth. 3 U 19" rack

EN

- 7 -

160129_FS-4256E_MANUAL_(EN)_Maquetación 1  1/2/16  8:29  Página 7

Summary of Contents for FS-4256E









Reviews: