background image

114

Smoke safety device interception

To restore functioning unscrew the lid of the thermostat and reset the button underneath (fig.

6). If the failure should occur again, call the Authorised Technical Service for assistance.

6 5

Default values

To  take  the  setting  to  the  default  values,  press  the

and 

keys  at  the

same time for at least 3 seconds. As confirmation a sign will appear on the display.

19

ATTENTION

The values of the following  line numbers previously entered will be lost.

• Temperature and time programme 

to

• Vacation period

1

10

18

Vacation function

To enter the number of days of absence.

In the display the vacation symbol will be shown (

), on the left the day of activa-

tion (1 = Monday/7 = Sunday) and on the right the number of vacation days.

18

During the vacation the regulator will be on the availability mode.

When the set days have elapsed, the regulator  will go on to the automatic function.

NOTE:

The vacation period may be cancelled by pressing a key of the operating mode.

Current values

Display and setting of the gradient of the heating characteristics curve. 

When the room temperature set is not reached choose the gradient 

indicated in point 2.7.3

Display of the current boiler temperature.

Display of the current power of the burner and of the current operating mode

(

= = heating/

= hot-water service)

15

16

1 7

Setting the time

To set the current day of the week

(1 = Monday/7 = Sunday)

To set the current hour

To set the current minute

Once the hour is completed, the setting of the hour changes.

12

13

14

With 

and 

keys the current hour is regulated. Pressing these keys together, the

regulation is speeded up in an increasing sense.

1

0

Display of the functioning faults on the display

Starting failure

Turn  the  selector  CR/OFF/SUM/WIN/UNBLOCK  from  the 

“LOGO”

control  panel  to  the

unblock position (

) to restore functioning (fig. 3). If the failure should occur again, call the

Authorised Technical Service for assistance.

Thermostat safety interception

Turn the selector CR/OFF/SUM/WIN/UNBLOCK of the 

“LOGO”

control panel to the unblock

position (

) to restore functioning (fig. 5). If the failure should occur again, call the Authori-

sed Technical Service for assistance.

Summary of Contents for LOGO 22 OF





























Reviews: