background image

10

Cleaning bin before use

  1.  Wipe storage area with Solution A.
  2.  Rinse thoroughly with clear, potable water.
  3.  Wipe with Solution B to sanitize.

Periodic cleaning of dispenser

Recommended daily cleaning of drain pan

  1.  Remove all debris from drain pan.
  2.  Pour 1 gallon (4L) hot water into drain pan to keep drain lines clear.

Recommended weekly cleaning

  1.  Remove drain pan and grille and wash with Solution A. Rinse thoroughly.
  2.  Pour a solution of one cup (8oz/237ml) household bleach mixed with one gallon (3.8L) hot water into drain 

pan to help prevent algae growth in drain lines.

Recommended quarterly cleaning (every 3 months)

 
  1.  Turn power switch to OFF position and remove top from dispenser.
  2.  Remove ice from storage area.
  3.  Remove dispense chute cover, chute, auger motor assembly, auger and auger tube (page 11).
  4.  Remove drain pan, grille, dispense wheel and cover plate (page 12).
  5.  Clean all components and bin storage area with Solution A, rinse thoroughly with clear water and sanitize 

with Solution B.

  6.  Remove clean-out plug from drain line tee on side opposite dispense tower and let bath drain.
  7.  Use a bottle brush to clean coil with Solution A, then rinse and sanitize with Solution B.
  8.  Reinstall clean-out plug in drain line tee.
  9.  Pour potable water into bath to submerge coil.

Putting unit back in service after quarterly cleaning

 1. Reassemble components.
  2.  For manual load units, fill unit with an approved ice (see caution statement on page 3). 
  3.  For automatic load units with R400A/W (R404A refrigerant) icemakers, turn bin signal switch(es) and 

dispenser power switch to ON position and allow storage area to fill.

  4.  Push dispense button or lever to test that dispenser is functioning properly.

Quarterly cleaning of icemaker system

Units equipped with icemakers require cleaning of icemaker system at least every three months, and 
more often if local water conditions dictate. Failure to clean icemaker system will result in decreased 
performance and potential damage to icemaker. Refer to Icemaker Operation and Service Manual.

DO NOT run plastic parts (drain pan, dispense chute cover, dispense wheel) 
through a dishwasher.

!

On push-button units, remove dispense switch from dispense chute cover 
before cleaning chute cover.

!

Summary of Contents for U155N Series





















Reviews: