Foerster TAK5-CH1-25 Instruction Manual Download Page 99

Page: 99 / 226

Transmitter and animal management

7. Confirm

register?

with

to register the animal.

8. Press

to confirm the query on the right.

7.2.2

Registering the animal automatically

If a non-registered animal enters the feeding station for the first

time, it can automatically be registered. Three different auto-

matic registration modes can be selected. The following three

subchapters contain a more detailed description of these modes.

Below you will find a synoptical table.

Note:

If no animal scales is available, an average weight

gain based on experience will be calculated.

animal 20/a

in group A

register?

Note:

On the day of registration the animal will receive,

distributed over the day, exactly the amount of feed to

which it is entitled on the first day. If you have entered

correction days, the animal will receive the amount of

feed to which it is entitled on the corresponding day.

register

animal

automatic

Automatic registra-

tion mode

Transmitter number in the identification

available

unknown

deactivated

warning

unknown

transmitters

warning

unknown transmitters

available transmit-

ters

the animal will be reg-

istered

warning

unknown transmitters

all transmitters

the animal will be reg-

istered

the transmitter will be entered, a new animal

number will be allocated, the animal will be

registered

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands