Foerster TAK5-CH1-25 Instruction Manual Download Page 185

Page: 185 / 226

Failures and warnings

185

2. The cable between the motor and the board used to transfer

the pulses has been possibly removed or it may be defective.

12.2.8

Scales (SC)

This message is displayed if the automatic feeder is not able to

communicate with the scales control via the CAN-bus. A reason

for it may be that the CAN-node is switched off or the address of

the scales control does not correspond to the one entered in the

setup of the automatic feeder.

see

4.8.3

Scales, page

12.2.9

Water meter

12.2.10 Mixer emptying

If the mixer cannot be emptied because e.g. the discharge is

clogged or the feeding pump is defective, the warning on the

right will be displayed.

> Check all feed-supplying components leading from the mixer

to the mixer draining valve resp. from the mixer to the teat for

clogging and remove them.

> Check the feeding pump. In

feed. pump: start?

press

> heck the mixer draining valve (if available). In

mixer drain

open?

press

> Check the bar electrode.

> In

water boiler: start?

press

to fill the mixer with some

water.

> In

mixer: drain?

press

warning

scales

warning

water meter

pulses

water HE: start?

water bo.: start?

warning

mixer emptying

feed. pump: start?

mixer drain: open?

water bo.: start?

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands