Foerster TAK5-CH1-25 Instruction Manual Download Page 167

Page: 167 / 226

Animal control

167

11.6

Checking newly housed animals

This menu shows the newly registered animals. Here you can

view different information resp. carry out animal-specific

changes. You can

> adjust the

animal no.

and move the animal to another

group

> enter deviations in

feed

and

conc(entration)

> check the milk ratio.

> select and adjust a prescription in

additive

> change calf’s weight in

weight

> press

plan day

to access a submenu. There you can

view the following information resp. change the values:

feed. day

the number of days passed by since regis-

tration is displayed.

correct

enter the desired number of days.

In the following lines you can check:

animal’s

plan day

after correction,

when the

plan end

eis achieved,

the

feed

quantity and feed

concentration

fed to the an-

imal today,

the current

milk

ratio of the feed portion.

Date

and time of animal’s registration.

> In

confirm

press

to delete the animal from the list of the

newly registered animals.

< 5562/A1 >

6.0 L

no.: 2213258

animal no.: 5562

group: A

feed: 6.0 L

conc.: 135 g/L

milk ratio: 100 %

additive 1: no

additive 2: no

weight: 48 kg

plan day: 8

time: 13:24:54

date: 29.04.09

confirm?

< 5562/A1 >

6.0 L

feed. day: 8

correct: 0 days

plan day: 8

plan end: 73 days

feed: 8.0 L

conc.: 135 g/L

milk ratio: 100 %

Note:

If you want to

extend

the total duration of feeding,

enter a

negative figure

. If you wan to

shorten

it, enter

positive figure

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands