Foerster TAK5-CH1-25 Instruction Manual Download Page 154

Page: 154 / 226

154

Diagnostic

check whether the feed sensor of the gradient or the servo

control is active/inactive,

> view the control unit allocated to the feeding station,

> check the animal scales allocated to the feeding station.

> If the feeding station is an Intelligent Feeding Station (IFS) or

an IFS-compact unit, the CAN-bus-address can be trans-

ferred to this control of the feeding station(s) resp. the con-

centrate station (see

4.8.1.2

IFS-F(eeding stations), page

or see

4.8.1.3

IFS-compact unit for four feeding stations,

page

resp. see

4.8.2

IFS-concentrate stations, page

To do so, in

search?

press

diagnostic

stations > feed

F-station 1

...

2. To check the identification (antenna test), hold a transmitter

within the range of the antenna. The line

no. ‡

displays the

transmitter number.

<F-station 1>

no. ‡: 1456

pump: start?

teat slider: open?

Calf Protect: close?

feed sensor: active

control: [IFS-F 1]

scales

search?

Note:

If the transmitter number is not identified, proceed as

follows:

1. Check in the setup whether the correct identification sys-

tem has been selected.

2. Check the data lines between the antenna and the auto-

matic feeder for damages.

3. Check in the setup the allocation of the station where the

identification causes problems.

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Brands by name

Popular brands