Foerster TAK5-CH1-25 Instruction Manual Download Page 153

Page: 153 / 226

Diagnostic

153

2. In the second line the state of the queried electrode is dis-

played. Press

start?

in water bo.

, water HE or milk

. Use the

lines below to dose a liquid feed component into the mixer jar

and to check whether the corresponding electrode shows re-

action. To subsequently empty the mixer jar, in

mixer: emp-

ty?

press .

•

Water meter: Here you can check whether the water meter

is working properly. To do so, open the water valve. In

pulses

the pulses of the water meter are displayed. To subsequently

empty the mixer jar, in

mixer: empty?

press

10.4 Checking the stations

This menu is structured as follows:

•

Feeding stations (F-stations)

•

Concentrate stations (C-stations)

In addition, you can check the animal scales (SC) – if available

– mounted in the corresponding station.

10.4.1

Feeding stations

Here you can

> check, whether the identification of the feeding station is

working properly,

start the servo pump,

open the teat slider,

close the gate of CalfProtect,

> open the box valve,

supply electrode

state: free

milk: start?

water HE: start?

water bo.: start?

mixer: empty?

water meter

pulses: 23

water HE: start?

water bo.: start?

mixer: empty?

Note:

Changes in state or temperature are immediately

displayed. Consequently, fault occurence is narrowed

down.

stations

feed

concentrate

stations

feed

concentrate

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Brands by name

Popular brands