Foerster TAK5-CH1-25 Instruction Manual Download Page 146

Page: 146 / 226

146

Cleaning

9.6

(Box) valve cleaning

This menu is only displayed if in

setup

circ. valve

you

selected

valve

The box valves can be all-automatically cleaned even if the auto-

matic feeder is not equipped with the kit for fully automatic heat

exchanger cleaning. In that case, the box valves are only

cleaned with cold water. No detergent will be added.

cleaning

valves

2. In

start after

enter the time that should elapse after the last

portion has been dispensed before cleaning starts running.

3. In

duration

enter how long the valves should be cleaned.

9.7

Sponge cleaning

If the automatic feeder is not equipped with the fully automatic

heat exchanger cleaning or the latter is deactivated, the stainless

steel coil of the heat exchanger should be daily (recommended!)

cleaned with the sponge ball to remove deposits and milk resi-

dues. The sponge ball is used as a mechanical cleaning aid.

Start after

Intensity

Default value:

30 min

medium

Range:

0 to 120 min

low, medium, high

valve cleaning

start?

start after: 30 min

duration: 3 sec

Start after

Duration

Default value:

30 min

3 sec

Range:

0 min, 5 to 120 min 1 to 10 sec

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands