Foerster TAK5-CH1-25 Instruction Manual Download Page 14

Page: 14 / 226

Introduction

1.7

Abbreviations used in this instruction manual

Abbreviation

Meaning

abs.

absolute

add. disp.

additive dispenser

B-ant.

B-antenna

C-station

concentrate station

circ. pump

circulation pump

cl. mixer

mixer cleaning

deterg. pump

detergent pump

dos.

dosage

drain. time

draining time

empty v. teat

empty via teat

F-station

feeding station

feed. speed

feeding speed

gr A (B)

group A (B)

gradient

gradient control

heat exchanger

interval

IFS-C

Intelligent Feeding Station for concentrate

IFS-F

Intelligent Feeding Station for feed

milk powder

MAP

manual training pump

max.

maximum

min. temp.

minimum temperature

mixer drain

mixer draining valve

not

No.

number

period or prescription

powd. motor

powder motor

rel.

relative

servo

servo control

SNTR

designation of IFS-compact unit

temp.

temperature

train. pump

training pump

w. add.

with additive

w. entit.

with entitlement

water bo.

boiler water

with add.

with additive

w.o. add.

without additive

w.o. entit.

without entitlement

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Brands by name

Popular brands