background image

19

FDS AMPLIFIERS

U s e r   m a n u a l

WARNING

•  Do not operate any functions which may distract you while driving. 

Functions requiring sustained 

attention must only be used when the vehicle is at a complete standstill. Always make sure to stop 

your vehicle in a safe place before operating these functions. Failure to do so may cause an accident.

•  Keep the volume at a low level to be able to hear exterior noises while driving the vehicle. 

Failure 

to do so may cause an accident.

•  Do not open your FDS amplifier or make any modifications to the product. 

Failure to do so may 

cause an accident, a fire or an electric shock.

•  Only use your FDS amplifier with 12V mobile applications. 

Any use other than the intended use may 

cause a fire, an electric shock or injury.

• Use fuses with the adequate amperage. 

Failure to do so may cause a fire or an electric shock.

•  Do not obstruct the heat sink on your FDS amplifier. 

Internal overheating may occur and cause a fire.

•  Wire the connections correctly. Make sure you use the appropriate wire gauge and type of cable. 

Failure to do so may cause a fire, injury and/or material damage.

•  Do not use nuts or bolts on steering or breaking systems, tanks, seat-belt anchor points or other 

safety elements for connecting the ground. 

Using of these parts as ground may deactivate the 

vehicle’s control system and cause a fire or other damage.

•  Keep small parts which could be swallowed, such as bolts, accessories or screws out of the reach of 

children. 

Swallowing such parts may cause to serious injury. If swallowed, consult a physician.

•  Before beginning installation, disconnect the negative terminal of the battery to avoid any risk of 

injury, fire or material damage. 

(fig. 1)

fig. 1

Summary of Contents for FDS 1.350





























































Reviews: