background image

INSTALLATION INSTRUCTIONS FOR

CONCRETE LOG MODELS LBG(18,24,30)-BM

Save this manual for future reference

Figure 4 - Installing Left Ember Bed Log

Left Ember 

Bed Log

5.  The right ember bed log 24" & 30'' (D-047) 

has a hole in the log that sets on the grate 

finger and the other end rest on the fire

-

place floor, place log as shown in Figure 5, 

page 2. The right ember bed logs for 18" 

(D-072) has a groove on the side that sets 

on the ember bed pan and the back of the 

log needs to rest against the front of the 

base. Make sure the flame from the ember 

pan does not touch the ember bed log.. The 

back side of this log needs to rest against 

the front of the base assembly, make sure 

the flame from the ember pan does not 

touch the ember bed log.

3.  Place front left (18" D-064, 24" D-057 & 30" 

D-038) and front right (18" D-065, 24" D-058 

& 30" D-039) logs as shown in Figure 3.

Figure 2 - Installing Fiber Ramp Log 

Figure 3 - Installing Left/Right Front Logs

Ramp Log

Left Front 

Log

Right Front Log

Metal 

Tab

4.  Place left ember bed log (18" D-073, 24" & 

30" D-048) as shown in Figure 4. The log has 

groove on one side that sets on the ember 

bed pan. The back side of this log needs to 

rest against the front of the base assembly. 

Make sure the flame from the ember pan 

does not touch the ember bed log.

Note: Your appliance may vary from model 

shown but log placement will be the same.

1.  Before placing any logs on the chassis you 

will need to remove the Air Shield located 

on the left side near the rear burner as 

shown in Figure 1. The Air Shield is held in 

place with one screw, remove the Air Shield 

and place the screw back into the hole in 

the chassis. Place the Air Shield with you 

owner's manual and keep.

Figure 1 - Removing Air Shield 

Air Shield

Screw

2.  Place fiber ramp log in center of chassis 

as shown in Figure 2. The fiber ramp log 

can be identified by the shape and much 

lighter weight when compared to the other 

logs. The  log  must  sit  flat  on  the  black 

sheet metal and behind the left metal tab 

as  shown.  Make  sure  the  side  marked 

''BOTTOM'' is setting down.

Summary of Contents for LBG12-BM

Page 1: ... Right Front Logs Ramp Log Left Front Log Right Front Log Metal Tab 4 Place left ember bed log 18 D 073 24 30 D 048 asshowninFigure4 Theloghas groove on one side that sets on the ember bed pan The back side of this log needs to rest against the front of the base assembly Make sure the flame from the ember pan does not touch the ember bed log Note Your appliance may vary from model shown but log pl...

Page 2: ...tom to sit on the chassis and has to sit on the tab on the back of the right front The right middle log should have a recess area that fits around the ramp log as shown in Figure 7 8 The rear middle log 18 D 068 24 30 D 042 should fit between the ramp log and the rear burner The left and right middle logs have recessed areas for the rear middle log to sit into See Figure 8 There may be a small gap...

Page 3: ...og as shown The rear log has a projection that will fit into the recess area on the bottom of the top rear log see Figure 12 INSTALLATION Continued Figure 10 Installing Left Top Log Figure 11 Installing Middle Crossover Log Figure 12 Installing Top Rear Log Rear Log Left Top Log Left Middle Log Top Rear Log Rear Log Middle Crossover Log 10 Place the left top log D 046 onto the rear log and the lef...

Page 4: ...072 125852 05 D 047 125852 05 D 047 Log Right Front Ember Bed 1 125851 06 D 066 125852 06 D 040 125852 06 D 040 Log Left Middle 1 125851 07 D 067 125852 07 D 041 125852 07 D 041 Log Right Middle 1 125851 08 D 068 125852 08 D 042 125852 08 D 042 Log Rear Middle 1 125851 09 D 069 125852 09 D 043 125852 09 D 043 Log Rear 1 125851 10 D 046 125851 10 D 046 125851 10 D 046 Log Left Top 1 125851 11 D 070...

Reviews: