ASSEMBLY OF YOUR ELECTRIC FREE-FLIGHT SKY VOYAGER
WARNING: Read instructions carefully! Improper use of this product may result in personal injury or damage to the public.
WARNING: Choking hazard–small parts. Do not allow children under age 3 to play with the Sky Voyager. This model contains small
parts which could accidentally be swallowed and cause suffocation. Use with adult supervision.
Replacement Parts
HCAQ3281 Propeller (2)
HCAZ0313 for HCAA0313
Entire Contents © Copyright 2006
Requires 4 “AA”
Alkaline batteries
(Not included)
HCAA0313
WARRANTY
Hobbico, Inc. guarantees this kit to be free of defects in both material and workmanship at the date of purchase. This warranty does not cover any component parts
damaged by use or modification. In no case shall Hobbico’s liability exceed the original cost of the purchased kit. Further, Hobbico reserves the right to change or
modify this warranty without notice. In that Hobbico has no control over the final assembly, no liability shall be assumed nor accepted for any damage resulting from
the use of the final user-assembled product. By the act of using the user-assembled product, the user accepts all resulting liability. If the buyer is not prepared to
accept the liability associated with the use of this product, the buyer is advised to return this kit in new and unused condition to the place of purchase. Please inspect
all parts carefully before starting assembly! If any parts are missing, broken, or defective, or if you have any questions regarding assembly or flying of this airplane,
please call us at (217) 398-8970, and we’ll be glad to help.
™
①
①
INSTALL THE MAIN WING
③
③
PREPARE THE CHARGING UNIT
④
④
CHARGING INSTRUCTIONS
• Gently remove the wing cover.
• Remove the backing paper from
the double-sided tape strips on
the bottom of the fuselage.
• Carefully line the wings up so that
the seam will run along the center of
the fuselage and control surfaces
are towards the tail as shown.
Gently press the wings in place.
• Remove the backing paper
from the double-sided tape
strips on the wing cover and
gently press it back in place on
the bottom of the fuselage.
Note: The front edge of the
wing cover is thicker and
can be identified by the
double-sided tape.
②
②
INSTALL THE STABILIZER & RUDDER
Tape Strips
Tape Strip
• Remove the backing
paper from the double-
sided tape strip at the
rear of the fuselage
and put the stabilizer in
place as shown.
• Locate the two (2) strips of tape
in the accessory bag. Press-fit
the vertical fin in place and
secure it to the fuselage by
putting a strip of tape on either
side of the rudder as shown.
Tape Here
• Using a small Philips head screwdriver, loosen the battery door
screw and carefully remove the battery door from the charger unit.
• Install 4 fresh “AA” Alkaline batteries into the charger. Make sure
that the (+) positive and (-) negative poles match up correctly with
the diagram molded inside the battery compartment.
NOTE: Do not use rechargeable (Nickel Cadmium) batteries.
Do not mix old and new batteries.
Do not mix Alkaline, standard (Carbon Zinc), or
rechargeable (Nickel Cadmium) batteries.
• Carefully replace the battery door on the charger and retighten
the screw.
Before charging your Sky Voyager, be sure that
the ON/OFF switch is in the “OFF” position!
• Insert the charger into the charge socket located on the side of
the fuselage, next to the ON/OFF switch. The charging unit will fit
only one way so match the tab on charger with the notch on the
charge socket.
• Press and hold the button on the charger to charge the airplane.
On the first charge, only charge the Sky Voyager for 15 seconds.
For longer flights, you may increase the charge time up to 60
seconds. Release the button to stop charging.
• When charging is complete, remove the charger from the Sky
Voyager.
NOTE: Never charge the Sky Voyager for more than 60 seconds!
Charging for more than the suggested time may result in damage to
the plane’s internal battery pack or to the charging unit.
ON/OFF
Switch
Charger
Control Surface
™
