FTr10
接收机 Receiver
http://www.flysky-cn.com
Copyright ©2021 Flysky Technology co., ltd
FTr10 采用 AFHDS 3（第三代自动跳频数字系统），双天线双向
传输，它独特设计可节省安装空间，可输出标准 PPM、PWM、
i-BUS 和 S.BUS 信号。
FTr10 adopts AFHDS 3, Flysky's third-generation automatic
frequency hopping digital system. It uses a double-antenna
bidirectional transmission system and is uniquely designed
to save space and output standard PPM、PWM、i-BUS and
S.BUS signals.
产品介绍
Introduction
接收机概览
Receiver overview
用于连接接收机与模型的各个部件。
SENS：连接各传感器。
SENVO：输出 i-BUS/S.BUS 信号，连接扩展模块。
CH 1- CH 10：连接舵机、电源或其他各部件。
BIND：连接对码线。
Power：为飞控供电。
Ports used to connect the receiver to the various
components.
SENS: Connects to sensors.
SENVO: Output i.BUS/S.BUS signal, connect expansion
module.
CH 1 - CH 10: Connects the servos, power supply or other
components.
BIND: For bind cable.
Power: Flight controller power output.
CH 1- CH 7
Bind
CH 8-CH 10
Antenna
Antenna
Power
LED
产品规格
Product specification
通道个数：10
适用机型：固定翼 / 滑翔机 / 直升机 / 多轴
数据输出：PWM/PPM/i-bus in/i-bus out/S.BUS
无线频率：2.4GHz
发射功率：<20dBm（EU）
RF 标准：AFHDS 3
天线长度：103 毫米 *2( 双天线 ) 铜管天线
输入电源：3.5V ～ 12V
显示方式：LED 指示
在线更新：有
外形尺寸：52*28*22mm
机身重量：22g
安规认证：CE，FCC ID: N4ZFTR1000
Channels: 10
Model Type: Fixed wing/ glider / helicopter / drone
Data Output: PWM/PPM/i-bus in/i-bus out/S.BUS
RF: 2.4GHz
Transmission Power: <20dBm(EU)
RF standard: AFHDS 3
Antenna: 103mm*2
Input Power: 3.5V ～ 12V
Display: LED Indicator
Online Update: Yes
Dimensions: 52*28*22mm
Weight: 22g
Certification: CE，FCC ID: N4ZFTR1000
对码
Binding
1. 将对码线插入 BIND 接口；
2. 将电源线插入其他任意接口，接收机指示灯快闪表示进入对码
状态；
3. 将发射机进入对码状态；（发射机进入对码状态的方式可能不
同，请根据发射机的使用说明书进行操作）
4. 当接收机指示灯变为常亮时，表示对码成功。将对码线和电源
线从接收机取下。
5. 重新连接电源线至接收机。
6. 检查发射机、接收机、模型是否正常工作。如需重新对码，请
重复以上步骤重新对码。
1. Insert the bind cable into the receivers BIND port;
2. Plug the power cable into any other port, and the receiver's
LED will start to flash quickly
indicating that it has entered
bind mode.
3. Put the transmitter into bind mode; (See the transmitter's
instruction manual for more information)
4. Binding is successful when the receiver's LED will stop
flashing. Remove the power and bind cables from the
receiver.
5. Reconnect the power cable to the receiver.
6. Check to make sure that the transmitter and receiver are
working as expected, if there are any issues or unexpected
operation follow the steps above to bind again.
SENS
SERVO
“S”
“+”
“-”
强制更新短接口
（Force update interface）
