FGr4P
接收机 Receiver
http://www.flysky-cn.com
Copyright ©2021 Flysky Technology co., ltd
FGr4P 采用 AFHDS 3（第三代自动跳频数字系统），外置单天
线双向传输，它的设计小巧，便于安装。可输出标准 PWM、i-BUS、
S.BUS 和 PPM 信号。
The FGr4P uses AFHDS 3 (Third Generation Automatic Frequency
Hopping Digital System). It uses a single antenna with two-way
transmission capabilities and is designed to be compact and easy
to install. It can output standard PWM, i-BUS,S.BUS and PPM.
产品介绍
Introduction
接收机概览
Receiver overview
CH1- CH4：连接舵机、电源或其他各部件。
i-BUS/S.BUS：输出 i-BUS /S.BUS 信号 , 连接传感器和扩展
模块。
BIND：连接对码线。
Battery: 连接电源。
CH1 - CH4: Connects the servos, power supply or other
components.
i.BUS/S.BUS:Output i.BUS/S.BUS signal, connect sensor and
expansion module.
BIND: For bind cable.
Battery: Connect the battery.
对码
Binding
1. 将对码线插入 BIND 接口；
2. 将电源线插入其他任意接口的正负极，接收机指示灯快闪表示
进入对码状态；
3. 将发射机进入对码状态；（发射机进入对码状态的方式可能不
同，请根据发射机的使用说明书进行操作）
4. 当接收机指示灯变为常亮时，将对码线和电源线从接收机上取
下；
如果发射机是单向，则接收机指示灯为慢闪状态。
5. 将电源线重新连接至接收机，接收机指示灯常亮表示对码成功；
6. 检查发射机、接收机、模型是否正常工作。如需重新对码，请
重复以上步骤重新对码。
1. Insert the bind cable into the receivers BIND port;
2. Plug the power cable into any other port, and the receiver's
LED will start to flash quickly indicating that it has entered
bind mode;
3. Put the transmitter into bind mode; (See the transmitter's
instruction manual for more information)
4. Binding is successful when the receiver's LED is on
continuously. unplug the power and bind cables from the
receiver;
If the transmitter is one-way the receiver status indicator will
flash slowly;
5. Reconnect the power cable to the receiver;
6. Check to make sure that the transmitter and receiver are
working as expected, if there are any issues or unexpected
operation follow the steps above to bind again.
接收机接口示意图：
Receiver interface diagram:
LED
Anntena
产品规格
Product specification
通道个数：4
适用机型：车、船
数据输出：PWM/i-BUS/S.BUS/PPM
无线频率：2.4GHz
发射功率：<20dBm（EU）
RF 标准：AFHDS 3
天线类型：外置天线
输入电源：3.5V ～ 8.4V
显示方式：LED 指示
在线更新：是
外形尺寸：29*22*16.2mm
机身重量：8g
安规认证：CE，FCC ID: N4ZFGR4P00
Channels: 4
Model Type: Car/Boat
Data Output: PWM/i-BUS/S.BUS/PPM
RF: 2.4GHz
Transmission Power: <20dBm(EU)
RF Standard: AFHDS 3
Antenna: External Antenna
Input Power: 3.5V~ 8.4V
Display: LED Indicator
Online Update: Yes
Dimensions: 29*22*16.2mm
Weight: 8g
Certification: CE，FCC ID: N4ZFGR4P00
CH2-CH4
i-BUS/S.BUS
BIND
CH1-PPM/PWM
Battery
S（信号脚 /
Signal Pin
）
+（电源正极 /Positive power terminal）
-
（电源地 /Power ground）
强制更新短接口（Force update interface）
强制更新短接口 (Force update interface）
