SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [email protected]
RF Wireless Remote Control Kit (Model 0020481)
Package Include:
1 x Receiver: S2PF-DC06 / S2PF-DC09 / S2PF-DC12 / S2PF-DC24
1 x Transmitter: CV-6-2
1 x User manual
Features:
Application: It can be used in rolling blinds, rolling doors, projection screens, awnings, pumps, winches, conveyors or other appliances and
equipments with DC motors, it can remote control DC motor rotates in the positive or reversal direction.
Wireless control, easy to install.
Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.
You can rotate two motors separately in the positive or reversal direction with the transmitter (remote control) from any place within a reliable distance.
The RF wireless signal can pass through walls, floors and doors.
High Power: Each channel can work at maximum current 30A.
With limit control
terminal
s: You can connect limit switches or sensors to stop the motor.
With
wired control terminal
s: You can connect manual switches or external devices (with low level output signal, such as sensors) to control the
motor.
Use an 8-bit microprocessor designed and developed with low-power and high-speed CMOS technology.
With characteristics of reverse power protection and over current protection.
Reliable control: The receiver only works with the transmitter which use same code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.
Receiver Parameters:
Model No: S2PF-DC06 / S2PF-DC09 / S2PF-DC12 / S2PF-DC24
Control Mode: Latched or Momentary
Coding Type: Fixed code or learning code
Coding Setting: By learning
Power Supply (Operating Voltage): DC6V (S2PF-DC06), DC9V±1V (S2PF-DC09), DC12V±1V (S2PF-DC12), DC24V±1V (S2PF-DC24)
Output: DC6V (S2PF-DC06), DC9V (S2PF-DC09), DC12V (S2PF-DC12), DC24V (S2PF-DC24)
Working Frequency: 315MHz / 433MHz
Channel: 2 CH, can work with 2 DC motors
Static Curr
ent: ≤6mA
Maximum Working Current: 30A / each channel, so motor's
maximum starting current can not exceed 30A.
PCB Size: 170mm x 109mm x 25mm
Case Size: 200mm x 120mm x 53mm
Note:
1. The receiver can work with different transmitters. When you set the receiver in momentary mode, it should work with four button transmitters, such
as model C-4 (100M), CWB-4 (50M, waterproof), CP-4 (500M), CV-4-2 (500M), or CB-4 (1000M) etc. When you set the receiver in latched mode, it
should work with six button transmitters, such as model CP-6 (500M), CV-6-2 (500M), or CB-6 (1000M) etc.
2. With a transmitter (such as CV-6-2) to form a complete set, the working distance can reach 500M in an open ground. The maximum working
distance 500M is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by
trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may or may not reach 500M. If you
want to have a further working range, you can install an external antenna to the receiver, and you also can use a powerful transmitter, such as CB
transmitters.
Transmitter Parameters:
Model No.: CV-6-2
Button: 6
Remote Control Distance: 500m / 1500ft (theoretically)
Encode: Fixed code by soldering
Unit Size: 110mm x 50mm x 18mm
Power Supply: 1 x 23A -12V battery (included, can be used for 12 months)
Usage (with transmitter CV-6-2):
Connect the positive pole of DC
power supply to terminal “+” of INPUT, and connect the negative pole of DC power supply to terminal “-” of INPUT.
Connect terminals
“A1” and “B1” to motor 1; connect terminals “A2” and “B2” to motor 2. You can exchange motor's two wires to change the rotating
direction of motor.
Setting control mode Latched: Do not connect Jumper-1 (CN1) or Jumper-2 (CN2)
Press button
▲
on the left: motor 1 rotates in positive direction.
Press button
▼
on the left: motor 1 rotates in reversal direction.
Press button
■
on the left: motor 1 stops.
Press button
▲
on the right: motor 2 rotates in positive direction.
Press button
▼
on the right: motor 2 rotates in reversal direction.
Press button
■
on the right: motor 2 stops.
