Code:
Operation:
CCT:
CRI: Weight:
G6LED300
AC-POWERCON 3000K- 5600K ≥95 10
kg (22.2 lb)
Specifications and performance
G6LED127
8 LEAF BARNDOOR
G6FLT059
SAFETY CABLE (2)
Display and buttons
Fuses and power consumption
G6LED128
GEL FRAME
G6FLT262
C-CLAMP
G6CNT154
AC CORD WITH
POWERCON CONECTOR
16 ft (4.82 m)
VegaLux 300 HP Bicolor
®
-
Operation Manual
The VegaLux 300HP BICOLOR is self-adjusting for voltages between 90-240VAC
NOTE:
Most electrical equipment briefly draws a larger amount of electrical current during startup (ignition). Please refer to the chart to confirm that your
electrical wiring is sufficient for the units used. All fuses must be rated at 250VAC.
VegaLux 300 HP Bicolor
®
50.2 cm
19.76”
33.1cm
13.03”
45.3 cm
17.83”
31.2 cm
12.28”
Functions
The VegaLux 300 HP BICOLOR unit has a liquid crystal display to visualize its
functions.
MENU: Returns to the previous menu.
ENTER: Allows access to the selected menu and saves and confirms the
desired value.
UP: Allows navigation through the different menus and submenus.
Increases the selected value.
DOWN: Allows navigation through the different menus and submenus.
Decrements the selected value.
CCT: Rotate the knob left and/or right to modify the color temperature
value in a range of 300Ok-5600K. Press for fine adjustment. Press 2 times
quickly to select between 3000K-5600K.
DIM: Turn the knob left and/or right to modify the intensity value from 0 to
100%. Press for fine adjustment. Press 2 times quickly to select between
0%-100.
ZOOM: Turn the knob left and/or right to modify the angle of the light
beam from 25º to 55%. Press 2 times quickly to select between 25º-55º.
If there is no manipulation of the knobs and/or buttons for 1 minute, the
display screen will go into "standby".
5 A @ 250 VAC
346
90-240
ELECTRICAL MEASUREMENTS
Current [A]
Fuse
Power [W]
Voltage [VAC]
2.89 A @ 120 VAC / 1.44 A @ 240 VAC
Each fixture comes with:
G6FLT057
STAND MOUNT SPIGOT
5/8”
Warnings
The Vegalux 300 HP BICOLOR is a professional lighting system. Read these instructions, as well as any applicable accessory
instructions and warnings before operating the unit:
Do not leave the device unattended.
For fixed (stationary) use in studios, theaters, and similar places.
Not for home use.
Use for photographic lighting (TV, video, and film)
Always unplug the unit before changing the fuse.
Do not use near standing water.
Never remove the ground pin from the plug.
Do not interfere with the ventilation of the unit.
Do not operate the unit with barndoors closed.
Make sure the clamp is tight to the yoke.
Always use the safety cable when connecting to pipes or vents.
Always use it with the supplied AC cord.
Avoid looking directly at the luminaire (LED source).
General recommendations
1.- Do not operate this product if it is damaged.
2.- Avoid contact with water or other liquids to protect yourself from electric shock.
3.- You must turn the unit off before connecting it to the electrical network; also, when removing the unit from a grid or
tripod, turn it off before disconnecting it from an electrical network.
4.- In case of failure or malfunction, to avoid electric shocks, Do not disassemble the unit; call your FLUOTEC®
AUTHORIZED SERVICE CENTER.
Improper assembly or disassembly of this unit may cause a malfunction.
5.- Using accessories not designed or recommended by FLUOTEC® may cause dangerous conditions or damage the device.
Cleaning
CHASSIS.
Use a damp, almost dry cloth to remove dust and any stains.
NEVER USE ABRASIVE FIBER AND NEVER USE SOLVENTS; they can damage the appliance or its finish.
Problems, repairs and information.
Repairs, problems, suggestions and requests for brochures, catalogs, illustrations and parts lists can be handled through
your authorized FLUOTEC® dealer or directly through FLUOTEC®. Electrical repairs must be carried out only by FLUOTEC®
or a qualified electrician.
FLUOTEC®
TEL. +1-213-296-4202
email : [email protected]
