manualshive.com logo in svg

Fluke SMFT-1000, User Manual, Page: 27 / 48

Share
Download
Fluke SMFT-1000 User Manual Download Page 27

Multifunction PV Analyzer

Test Setup

23

Quick V

OC

/I

SC

 Measurement

You can take a quick V

OC

/I

SC

 measurement without connecting the Irradiance Meter or 

PV model. Pass/Fail limits or Irradiance data do not show with this type of measurement.
To take a measurement:
1. Turn the rotary switch on the PV Analyzer to 

V

OC

/I

SC

.

2. Connect the test leads to the solar panel. The V

OC

 measurement automatically shows on 

the display.

Tip: Push 

 to see a connection diagram.

Voltage symbol is on when voltage is 

≥

50 V.

3. Push 

 to start the I

SC

 measurement.

The V

OC

 and I

SC

 results show on the display. The Pass/Fail icons do not show in this 

configuration.

4. Push 

 to save the results to memory.

A confirmation message with ID number shows on the display and then returns to the test 

screen.

V

OC

/Operational Current Measurement

Operational current as alternative method for I

SC

 as required by IEC 62446-1 Clause 6.5.3. 

To take a measurement:
1. Connect the PV string to the inverter and switch the system to on and normal operation 

mode (inverter must be at maximum power point).
It is useful to connect two Y-connectors in between so you can measure the string voltage 

in parallel.

2. Turn the rotary switch to 

V

OC

/I

SC

.

3. Connect the test leads to the solar panel.

The V

OC

 measurement automatically shows on the display.

Tip: Push 

 to see a connection diagram.

Shop for Fluke products online at:

1.888.610.7664

www.

MyFlukeStore

.com

Summary of Contents for SMFT-1000

















































Reviews:

No comments