manualshive.com logo in svg

Fluke SMFT-1000, User Manual, Page: 21 / 48

Share
Download
Fluke SMFT-1000 User Manual Download Page 21

Multifunction PV Analyzer

Test Setup

17

Continuity of Protective Earthing and Equipotential Bonding Conductors

For accurate measurements, always compensate the resistance of the test leads before you 

make measurements:
1. Turn on the PV Analyzer.

2. Turn the rotary switch to 

.

3. Zero (short) the green lead and yellow lead.

4. Push 

.

For more information, see 

Figure 1

.

5. Follow the on-screen prompts. 
6. To assign Pass or Failed status, set the regulatory limits for the measurements.

Note

You cannot change the limits after the measurement is taken. If you change the limit, 

you must repeat the measurement.

Set Limits

The regulatory limit is based on the length of the cable used in the test.
To set:
1. Turn on the PV Analyzer.

2. Turn the rotary switch to 

.

3. Use 

 

 

 or 

 to highlight an option.

4. Push 

 to edit the option.

The Manual Entry screen shows on the display.

5. Push 

 to open the Adjustment menu.

6. Use 

 to change the value.

7. Adjust the Cross Section and Material options as required.

8. Push 

 to toggle between the Manual Entry screen and Auto Calculate limit.

9. Push 

 to save the calculation and return to the 

 Measurement screen.

Shop for Fluke products online at:

1.888.610.7664

www.

MyFlukeStore

.com

Summary of Contents for SMFT-1000

















































Reviews:

No comments