Fluke P5500 Series User Manual Download Page 13

 

Hydraulic Comparison Test Pump 

 

Operation 

1

3

2

4

 

gjq002.eps 

Figure 2. Test Port Insert 

Table 3. Test Port Insert - Parts List 

Item Description 

P5515 

P5515-V P5515-EP 

1 O 

Ring 

3865142 

3865163 
 

3867888 

Test Port Insert 

3919892 

— 

— 

3 O 

Ring 

3883397 

3883521  3867895 

4 Test 

Port 

3918298 

— 

— 

To calibrate panel

-

mounted gauges with pressure connections in the rear, use an Angle 

Adapter (see Ancillary Equipment section). 

Operation 

Priming 

1.

 

Open reservoir valve (13) one turn counter

-

clockwise and turn screw press fully in. 

2.

 

Close valve (13) and turn screw press fully out. 

3.

 

Open valve and turn screw press fully in. 

Note 

During this operation, bubbles may appear in the reservoir, as trapped air 
is expelled. For large volumes, repeat steps 2 and 3 until no further bubbles 
appear. 

4.

 

With valve open, turn screw press fully out and close valve. The test pump is now 

ready for use. 

W

 Warning 

Turning the capstan out with the reservoir valve closed will 
generate approximately 15 inHg / 0.5 bar vacuum. If the DUT is 
vacuum sensitive, leave valve (13) open during priming 
operation. 

Summary of Contents for P5500 Series





















Reviews: