Fluke MicroMapper Pro Instruction Sheet Download | Manualshive

Page: 1 / 20

background image

PN 2828192 (English) July 2007

©

2007 Fluke Corporation. All rights reserved. Printed in Taiwan.

All product names are trademarks of their respective companies.

MicroMapper

™

Pro

VDV Cable Tester

Instruction Sheet

The MicroMapper Pro VDV (Voice, Data, Video) Cable Tester is a hand-held
test instrument that lets you verify and troubleshoot the wiring of twisted
pair and coaxial cables. The tester detects opens, shorts, miswires, and split
pairs. It also includes an analog toner function for locating cables with an
optional tone probe.

The tester comes with the following:

MicroMapper Pro VDV Kit (MMP-KIT)

•

MicroMapper Pro VDV tester with 6 AAA batteries

•

Remote identifiers #1 through #8

•

P

RO

3000

™

Tone Probe with 9 V battery

•

F-connector barrel adapter

•

MicroMapper Pro Instruction Sheet

1
2
3
...
»

Summary of Contents for MicroMapper Pro





















Reviews:

No comments

Related manuals for MicroMapper Pro

Brand: NEC Pages: 38

Brand: Fluke Pages: 5

Brand: Bodensteckdosen Systemtechnik Pages: 8

Brand: B.E.S.T-Germany Pages: 2

Brand: Amprobe Pages: 26

Brand: Amprobe Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands