manualshive.com logo in svg

Fluke Hart Scientific 1575 Super-Thermometer, User Manual

Share
Download
Fluke Hart Scientific 1575 Super-Thermometer User Manual Download Page 14

Science Park Eindhoven 5108

5692 EC Son

NETHERLANDS

Phone: +31-402-675300

Telefax: +31-402-675321

E-mail: [email protected]

Fluke Int'l Corporation

Service Center - Instrimpex

Room 2301 Sciteck Tower

22 Jianguomenwai Dajie

Chao Yang District

Beijing 100004, PRC

CHINA

Phone: +86-10-6-512-3436

Telefax: +86-10-6-512-3437

E-mail: [email protected]

Fluke South East Asia Pte Ltd.

Fluke ASEAN Regional Office

Service Center

60 Alexandra Terrace #03-16

The Comtech (Lobby D)

118502

SINGAPORE

Phone: +65 6799-5588

Telefax: +65 6799-5588

E-mail: [email protected]

When contacting these Service Centers for support, please have the following
information available:

•

Model Number

•

Serial Number

•

Voltage

•

Complete description of the problem

1575/1590 Thermometer Readout

User’s Guide

4

Summary of Contents for Hart Scientific 1575 Super-Thermometer





























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands