background image

 

REPEATER ENGLISH  701-8001-01^  08-14 

 

Page 

12

 of 

19

 

flowserve.com

 

 

8  TROUBLESHOOTING 

  

WARNING EXPLOSION HAZARD: DO 

NOT OPEN ENCLOSURE WHEN AN EXPLOSIVE 
ATMOSPHERE MAY BE PRESENT.  TURN OFF 
UNIT BY OPENING ALL FUSES PRIOR TO 
REPLACING BATTERY.

 

 

8.1  Loss of Communications 

Loss of communications with the repeater may occur 
for several reasons: 

 

Unit not powered up 

 

Unit out of range of receiver 

 

Receiver not configured correctly 

See solutions below to each of the possible causes: 
 

8.1.1  Unit Not Powered Up 

1.  Confirm that unit is powered up and 

receiving/transmitting data.  There are 4 LED 
lights on the repeater main board: 

a.  DECODE: indicates when a 

message is received from a 
transmitting unit (usually flickers 
often) 

b.  XMIT: indicates when the repeater is 

transmitting data 

c.  LO BAT: not used, remains off. 
d.  PWR: turned on when power is 

applied to the repeater. 

 

Figure 7: Repeater status lights 

 

If unit is powered up and 
receiving/transmitting data, proceed to next 
possible solution.  Otherwise, proceed to step 
2. 

2.  Verify battery and DC power supply/solar 

panel fuses are connected and not blown 
(see section  4  MAINTENANCE for how to 
turn on unit). 

3.  Use a voltmeter to read the battery voltage 

across the battery terminals.  If the voltage is 

below 11V, replace the battery according to 
instructions in section 4  MAINTENANCE. 

4.  Lastly, confirm the power source being used 

to charge the battery.  This procedure will 
vary depending on if your unit has a solar 
panel or AC power input. 

a.  AC Power: confirm the voltage 

coming out of the DC power supply is 
close to and above 12VDC.  If there 
is no output from the power supply, 
confirm that AC power is connected 
to the power supply.  If the AC power 
connection is working, the power 
supply will need to be replaced.  
Contact the Flowserve factory for 
assistance. 

b.  Solar Panel: confirm the power 

coming out of the power regulator is 
12VDC or higher.  If there is no 
output from the regulator, confirm 
that the solar panel is connected to 
the input and functional.  If the solar 
panel supply is working, the voltage 
regulator will need to be replaced.  
Contact the Flowserve factory for 
assistance. 

 

Figure 8: Measuring battery level on repeater 
using a voltmeter 

 

Summary of Contents for IPS Wireless




















Reviews: