background image

 

SYS11000OM Rev G 

 

 

[UF 350-HD, Generic Template]

 

FLIR Systems Polytech AB

 

 

 

Page 

14

 of 

70

 

Antennvägen 6 
SE-187 66 Täby  
Sweden 

 

1.4.2 

Thumb Joystick 

Legend 

 

FUNCTION

 

Description 

Screen Symbology 

 
Reference/Notes

 

(No legend) 

 

Control type

:  

X/Y analogue thumb joystick. 
 

Functionality

:  

Dual function. 

-

 

 
 
 

TURRET 

STEERING 

AZ & EL 

 

1)

  In 

STEER

  mode  the  thumb 

Joystick 

provides 

manual 

steering  of  the  TCU  line  of  sight 
in  azimuth  and  elevation  axis. 
The 

Joystick 

provides 

maximum  movement  rate  scaled 
appropriately 

for 

the 

active 

sensor

’s current field-of-view. 

 

Text field 1: 

STEER 

Bar Field 15: AZ Indicator 
Text Field 15a: ± 

##.#

o

  

(

Azimuth Angle)

 

Bar Field 14: EL Indicator 
Text Field 14a: ± 

##.#

o

  

(

Elevation Angle)

 

 
 
 
 
 
 
 
 

AIMPOINT 

REFINEMENT 

 

2)

 When the Auto Tracker or 

Geo-Target function is engaged 
and tracking, it provides the 
following tracker mode 
dependent functions; 
 

a)

 Correlation Tracking 

– Auto 

Tracker aimpoint refinement 
 

b)

 Centroid Tracking  

 
NOTE:

 This mode is tracking bounded 

objects, and the use of aimpoint 
refinement will most likely make the 
tracker to lose the target and revert to 
COAST mode (See § 1.4.16 and 1.5.1) 

 

c)

 Scene Lock 

–  

Auto Tracker aimpoint refinement 
 

d)

 Geo-Target  

–   

Aimpoint refinement 
 

Text field 1: 

TRACK 

 

 

 
 
 
Text  field 11: 

CORR 

 
 
Text field 11: 

CENTR

 

 
 
 
 
 
 
Text field 11:

 SCENE 

 
 
Text field 1: 

GEO 

 

Summary of Contents for UltraFORCE 350-HD







































































Reviews: