background image

iii

General Precautions

1. All warnings and instructions in this manual should be followed.

2. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents. Use a 

water dampened cloth for cleaning.

3. Keep enough space around the unit for ventilation. Slots and openings in the storage cabinet 

should not be blocked.

4. During lightning storms, or when the unit is not used for a long time, disconnect the power 

supply, antenna, and cables to protect the unit from electrical surge.

FCC CLASS A NOTICE

NOTE

This equipment has been tested and found to comply with the limits for a Class A digital device 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a commercial environment. This 
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used 
in accordance with the manufacturer’s instruction manual, may cause harmful interference with 
radio communications. Operation of this equipment in a residential area is likely to cause harmful 
interference, in which case you will be required to correct the interference at your own expense.

This equipment has been certified and found to comply with the limits regulated by FCC, EMC, and 
LVD. Therefore, it is designated to provide reasonable protection against interference and will not 
cause interference with other appliance usage.

However, it is imperative that the user follows the guidelines in this manual to avoid improper 
usage which may result in damage to the unit, electrical shock and fire hazard injury.

In order to improve the feature functions and quality of this product, the specifications are subject 
to change without notice from time to time.

www.flirsecurity.com/pro

Summary of Contents for DNB14UX2













































































Reviews: