manualshive.com logo in svg

FlightSafety LEARJET 45, Pilot Training Manual, Page: 43 / 539

Share
Download
FlightSafety LEARJET 45 Pilot Training Manual Download Page 43

shown on the EICAS display. The electrical

system volts and amps appear on page 2 of the

RMU engine displays (Figure 2-11).

Whenever the ENGINE PG1 display is auto-

matically displayed on the No. 1 RMU and

page 2 is subsequently selected, the display re-

turns to page 1 after 20 seconds. Returning the

RMU to the communication and navigation

function is accomplished with the RMU PGE

button. However, if the No.1 RMU is dis-

playing engine information due to an auto-

matic selection, that RMU will return to page

1 of the engine display 20 seconds after the last

pilot selection on the RMU. On the RMU en-

gine displays (page 2), the electrical data will

change color if out of limits, but will not be

boxed.

T h e   E I C A S / M F D   s y s t e m   S U M RY   p a g e

(Figure 2-10) displays VOLTS, left and right.

These two digital displays are an indication of

the voltage on the left and right essential

busses. Depending on what is powering the air-

plane electrical system, this can be an indi-

cation of airplane main battery volts, GPU

volts, APU volts or airplane generator volts.

A “L/R ESS BUS VOLTS” CAS message will

be posted if the voltage on the corresponding

bus decreases below 22 VDC or increases

above 29.5 VDC.

An indication of EMER-V (emergency bus

voltage) is displayed on the SUMRY page im-

mediately below VOLTS, left and right.

Emergency bus voltage can be monitored on

the EICAS/MFD display. The CAS also mon-

itors the emergency bus volts and will gener-

ate an amber “EMER BUS VOLTS” message

L E A R J E T   4 5

P I L O T   T R A I N I N G   M A N U A L

2-13

FOR TRAINING PURPOSES ONLY

FlightSafety

international

Honeywell

TUNE

SQ

DIM

1/2

STO

DME

TST

PGE

ID

Honeywell

TUNE

SQ

DIM

1/2

STO

DME

TST

PGE

ID

FUEL

HYD

M-B

SPL

FLP

MORE

10

3000

1400

20

1000

1450

ITT

O/P

76

550

80

550

MORE

6.5

R2

L3

TRIM-PIT

AIL

RUD

SAT

-15

°

 

310

AMPS

  65

EMER V

28.0

20.0

VOLTS

28.0

984

FF PPH

1002

60

OIL 

°

C

60

50.0

N2

50.0

75.0

N1

75.0

N1

IGN

75.0

IGN

75.0

Figure 2-11.   RMU Backup Engine Display Pages

Summary of Contents for LEARJET 45




























































































































































































































































































































































































































































































































































Reviews:

No comments