22
Parameter Value
Function
Current
•
Off
•
On/Comf.
•
Economy
•
N/A
•
Osstp
•
Nighttime
cooling
•
Support
operation
•
Test temp.
•
Damper
motion
•
Fire
•
Stop
•
Cool down
•
Startup
Operating mode:
•
Switched off.
•
Comfort operation (comfort
temperature setpoint)
•
Economy operation
(economy temperature
setpoint)
•
Extra operating mode;
not used.
•
Optimum start (activated
optimisation function).
•
Nighttime cooling activated.
•
Support operation; heating
or cooling activated.
•
Temperature test activated
for updating of duct sensor
temperature.
•
Fire damper test.
•
Fire mode (function
dependent on the parameter
setting for fire mode).
•
System stopped and
locked (process unit in start
phase, configuration not
done, alarm class danger,
emergency stop).
•
Cooling down.
•
System's start routine
activated.
Manual
operation
•
Auto
•
Off
•
Step 1
•
Step 2
•
Step 3
Manual operation via control
panel (possible only when Timing
program function <> Step+Temp).
•
Auto mode: The system
can be switched on via the
timing program, nighttime
cooling, etc.
•
System switched off.
•
System operation in step 1
(uses setpoint step 1 for
analogue outputs).
•
System operation in step 2
(uses setpoint step 2 for
analogue outputs).
•
System operation in step 3
(uses setpoint step 3 for
analogue outputs).
•
Manual operation via
control panel (possible
only when Timing program
function = Step+Temp).
Manual
operation
•
Auto
•
Off
•
Econ.St1
•
Comf.St1
•
Econ.St2
•
Auto mode: The system
can be switched on via the
timing program, nighttime
cooling, etc.
•
System switched off.
•
System in economy operation
in step 1 (uses setpoint step 1
for analogue outputs).
•
System in comfort operation
in step 1 (uses setpoint step 1
for analogue outputs).
Parameter Value
Function
Manual
operation
•
Comf.St2
•
Econ.St3
•
Comf.St3
•
System in economy operation
in step 2 (uses setpoint step 2
for analogue outputs).
•
System in comfort operation
in step 2 (uses setpoint step 2
for analogue outputs).
•
System in economy operation
in step 3 (uses setpoint step 3
for analogue outputs).
•
System in comfort operation
in step 3 (uses setpoint step 3
for analogue outputs).
Timing
program
•
Off
•
Step 1...
Step 3
Shows current command for
timing program (only if Timing
program function = Step).
Goes beside the parameter
setting for timing program.
Timing
program
•
Off
•
Econ.St1…
Econ.St3
•
Comf.St1…
Econ.St1
Shows current command for
timing program (only if Timing
program function = Step+Temp).
Goes beside the parameter
setting for timing program.
From BMS
•
Auto
•
Off
•
Step 1
•
Step 2
•
Step 3
•
Auto
Shows command from BMS
(only if Timing program function
<> Step+Temp). The value can
be set via the control panel even
if communication is inactive.
•
Auto mode: The system
can be switched on via the
timing program, nighttime
cooling, etc.
•
System switched off.
•
System operation in step 1
(uses setpoint step 1 for
analogue outputs).
•
System operation in step 2
(uses setpoint step 2 for
analogue outputs).
•
System operation in step 3
(uses setpoint step 3 for
analogue outputs).
•
Shows command from BMS
(only if Timing program
function = Step+Temp).
The value can be set via
the control panel even if
communication is inactive.
•
Auto mode: The system
can be switched on via the
timing program, nighttime
cooling, etc.
•
System switched off.
•
System in economy operation
in step 1 (uses setpoint step 1
for analogue outputs).
