Flexicon PF7 User Manual Download Page 119

Page: 119 / 179

25.20.4 Export all data

The following files will be created in top level folder of the USB flash drive.

•

Recipes.pf7

•

Settings.pf7

•

Users.pf7

Option only displayed when a USB flash drive is detected.

Exporting a recipes.pf7 file will replace recipes.pf7 currently saved
on the USB flash drive.

Exporting a settings.pf7 file will replace settings.pf7 currently
saved on the USB flash drive.

Exporting a users.pf7 file will replace users.pf7 currently saved on
the USB flash drive.

Table 26 - Required equipment - Export all data

USB flash drive (Refer to "USB devices" on page 41)

Keep a record of the administrator username and password at the
time of export. This will be required when importing the data.

PF7/PF7+ Peristaltic Filler with QC14 Pumphead User Manual

119

Summary of Contents for PF7




















































































































































































Search results

Summary of Contents for PF7

Reviews:

Flexicon PF7, User Manual, Page: 119 / 179

Search results

Summary of Contents for PF7

Reviews: