Flashforge Guider User Manual Download Page 76

Page: 76 / 76

Guider User Guide | www.ff3dp.com

Chapter 8: Supports and Service

Flashforge team is on standby and ready to help you with any challenges you may

have with your Guider. If the issues or questions are not covered in this User Guide,

you can seek for solutions on our office website or contact us via telephone.

There are solutions and instructions to common issues that can be found in our

knowledge base. Have a look first as most basic questions are answered there.

http://www.ff3dp.com

The FlashForge support team can be reached by e-mail or phone between the hours of

8:00 a.m. to 5:00 p.m. PST Monday through Saturday. In case you contact us during

after-hours, your inquiry will be answered the following business day.

Tel

：

86+579-82273989

ADD

：

No. 518, Xianyuan Road, Wucheng, Jinhua, Zhejiang

*When contacting support, please have your serial number ready. The

serial number is a bar code on the back of your Guider.”

Summary of Contents for Guider













































































Search results

Summary of Contents for Guider

Reviews:

Related manuals for Guider

Brands by name

Popular brands

Flashforge Guider, User Manual

Search results

Summary of Contents for Guider

Reviews:

Related manuals for Guider

Brands by name

Popular brands