Flashforge Guider User Manual Download Page 33

Page: 33 / 76

Guider User Guide | www.ff3dp.com

Chapter 5: About Software

5.1 Software Installation

5.1.1 Software Acquisition

Method 1:

To get the installation package from the USB disk in the toolkit.

Method 2:

Open the link below to download the installation package:

http://www.ff3dp.com

Steps: Support---Downloads---Guider FDM 3D Printer

5.1.2 Software Installation and Start-up

1. Decompress the zipped file or start the installation program, and then install the

software according to the direction.

2. Start the software with the start menu shortcut or by clicking the software icon.(See

5-1)

5-1

5.2 Exploring FlashPrint

5. 2.1 Machine Type Selection

! After starting FlashPrint, you need to select the target machine type first.

When you start FlashPrint, a dialog box will pop up. Just need to select Flashforge

Summary of Contents for Guider













































































Search results

Summary of Contents for Guider

Reviews:

Related manuals for Guider

Brands by name

Popular brands

Flashforge Guider, User Manual

Search results

Summary of Contents for Guider

Reviews:

Related manuals for Guider

Brands by name

Popular brands