Thanks to the very low battery con-
sumption, the LED lamp can light for
a very long time in the low brightness
mode. So it can be used for the fish-
ing place designation.
RGB LED lamp with a receiver -
FLACARP FL6-RGB
USER MANUAL
P 1
LED LAMP CONTROL
T I P
INTEGRATED RECEIVER
FALSE ALARMS
LOW BATTERY STATUS
AUTOMATIC SHUTDOWN
SPECIFICATIONS
Thank you
for purchasing the FLACARP
FL6-RGB. The lamp was created based
on the requirements of you, anglers. It is
equipped with powerful LEDs with the
possibility of adjusting the color. The in-
tegrated receiver allows you to remotely
control the lamp with up to ten FLACARP
transmitters.
Lamp can be switched ON after a bite,
after an alarm, or remotely controlled by
receiver RFX, e.g. lamp could be used like
a beacon. The distance can be up to 500
meters. You can reduce the brightness of
the LEDs so that the strong light does not
disturb you.
And the batteries? You will no longer have
to replace them! The lamp is equipped
with a powerful rechargeable Li-Ion bat-
tery. You can conveniently charge it using
a phone charger, from a car, or from any
power bank.
The lamp is designed not only for the
bivouac, but due to its 100% water resis-
tance, it can also be used as smart out-
door lighting. And when it falls into the
water, the lamp doesn‘t sink - it floats on
the surface :-)
The lamp is controlled by the green side
button.
Switching on / off
A short press of the button switches the
lamp ON, and it can be switched OFF in
the same way.
Brightness reducing
A short press of the button switches on
the lamp, and immediately following
next press of the button sets a lower
brightness level, suitable for reading, for
example. Lowering the brightness level
also extends the lighting time.
Color change
You can quickly change the color of the
LED by a double-click. The selected color
is then set as a default one after restart.
The color can be changed anytime.
Control button
Cover of the charging connector
with a strong magnet
Receiver switching on / off
by holding the button for 2 seconds.
Activation of the receiver is confirmed by
a brief flashing of the green LED, deacti-
vation by a brief flashing of the red LED.
Saving new device in memory
Hold down the button for 5 seconds
to enter the learning mode (LED light
flashes). You can now double-click to
select the color that should be lit by the
transmitter.
You can select white, red, green and blue.
The next step is the purple color - in this
step, the color already set on the bite
alarm is copied.
Save
Send a signal from the device you want to
save, that’s mean: turn ON the bite alarm,
alarm or press (short) the main button
on the receiver (while switched ON). The
device sends a signal and the LED light
save it in memory. Pairing is complete.
After saving, the learning mode is auto-
matically finished. Repeat the identical
procedure for saving other devices. If you
want to change the color of a specific
device, simply enter the learning mode
again and repeat the process. The color
of already stored device will be overwrit-
ten in memory.
Erase memory
Delete all learned devices from the
lamp’s memory. Hold down the button
for 15 seconds. A fast flashing red LED
indicates that the memory has been
erased.
The lamp reduces the false alarms.
The bite alarms turn on the light after
two or more succesive “bites” within 5
seconds. But the alarm from the mo-
tion sensor turns on the light immedi-
ately, as well as the RFX receiver control
responds immediately.
To prevent the permanently lit lamp in
the event of a false alarm, the lighting
time by a bite alarm or motion sensor
alarm is limited to 60 seconds.
Discharge of the battery is indicated
by a triple red LED brief flashing. If
the lamp does not respond at all, or
it switches OFF immediately when
switched on, it is discharged and
needs to be charged. Charge the lamp
before the first use.
The receiver of the lamp automatically
switches OFF 24 hours after the last ac-
tivity (after the last use). This function
prevents the lamp from discharging
when it is not used for a long time in
case you forget to switch OFF the re-
ceiver function.
■ LED type: RGB + white CREE®
■ Battery: Li-Ion 2000mAh
■ Charging: 5V / typ. 410mA
■ Charging time: approx. 6 hours (from
full discharge)
■ Lighting time (full brightness): up to 9
hours
■ Lighting time (reduced brightness): up
to 24 hours
■ Frequency: 868MHz
■ Range: up to 500 meters in open space
■ Operating temperature: 0 to 40ºC
■ Dimensions: 136 x 36 (42) mm
■ Weight: 124 g
+420 731 115 151 [email protected] flacarp.com flacarp flacarp tfe.cz
