Fitnest Sierra Pro, Assembly Instructions & User Manual

Page: 2 / 21

20
1/
Tools Required For Assembly
Assemble Item On a Clean Flat Surface
Need Two Or More People To Complete
- Please check you have all hardware before assembling.
- Please ensure you have the name of the item and hardware
part required and quantity.
- Please contact us by mail, if you have any questions, and we
will reply you ASAP.
- Enjoy your new purchase!
20
18/
6. Specifications
Tube Material
Expandable desk frame
Frame Adjustable Height
Depth of desk frame
Load Capacity
Speed
Steel
41.3" - 63.0" / 105 - 160cm
25.4"- 51.0" / 64.5 - 129.5cm
22.6" / 57.4cm
265 lb / 120kg
1.5" / s , 3.8mm / s
The system has anti-collision function in 3 strength rating of L2, L3, L4, and
strength of L2 is the lightest, and gradually increasing till to L4, the ex-factory
anti-collision strength rating settings is L3. Please note L1 is no anti-collision
function. See below to set anti-collision function strength rating. Press “M” and “2”
at the same time for 3 seconds and digital controller displays “---“, then press “ 2”,
it displays L2, the strength rating of L2 is set, waiting the controller shows height,
the setting is completed. The same operation set L3, L4, L1.
5. Anti-collision strength rating setting
a. Press and hold the DOWN button (about 5 seconds) until the LED displays
the flashing starting height.
b. Press the UP or DOWN button to increase or decrease the height (1unit / click).
c. Then press "M" and stop flashing, your desk is now ready to use.
Note: the LED display has a 0.1 tolerance.
ASSEMBLY INSTRUCTIONS
Dual-motor Electric Standing Desk
EP6000
M
12
34
><
If the error message persists after the reset procedure, please contact seller.
Below are the possible errors which can be displayed. The errors will only be dis-
played when a button is pressed.
E01
E04
E08
E10
E20
HOT
Error code
Description
Resolve
Lifting speed of two legs are not
able to sync or HALL signal failure
Leg 1 has overload, over-current
protection
Confirm that all wired connections are secure (legs to
cables, cables to control box).
Remove everything from the desktop and perform the reset
procedure outlined in the Digital Memory Controller section.
(better to hold for 18 minutes)
Leg 2 has overload, over-current
protection
Remove everything from the desktop and perform the reset
procedure outlined in the Digital Memory Controller section.
(better to hold for 18 minutes)
Leg 1 has collided and rebounded
The desk will automatically stop and bounce back 2 cm.
Perform the reset procedure outlined in the Digital Memory
Controller section
Leg 2 has collided and rebounded
The desk will automatically stop and bounce back 2 cm.
Perform the reset procedure outlined in the Digital Memory
Controller section
Over heating protection Hold for 18 minutes to restart
20
19/
7. Trouble Shooting
AC2-AA3_English V01拼 自翻版
20
2/
CAUTION / INFORMATION
1. This height adjustable desk has electric motors and is designed for use in
2. Make sure no obstacles are in the desk’s path.
Make sure the desktop is not touching any walls.
Make sure all cords are appropriate length to accommodate the change in height.
3. Do not sit or stand on the desk frame.
Do not crawl or lie under the desk frame.
4. Do not place any objects taller than 20” underneath the desk.
5. Do not open any of the components – the legs, control box or switch.
6. Make sure that the power supply is between 110v and 240v before plugging the
7. This product is designed with a duty cycle of 10% (2 min. on ,18 min. off).
8. Under no circumstances does the manufacturer accept warranty claims or liability
IMPORTANT: Please read this manual carefully.
control box into it.
dry work areas only.
claims for damages caused from improper use or handling of the desk frame.
There is a risk of injury and electric shock.
20
3/
SAFETY INSTRUCTIONS
1. Keep all electrical components away from liquids.
2. Keep children away from electric height adjustable desks, control units and
3. People who do not have the knowledge of the product or have reduced
4. Before trouble shooting
• Stop the desk legs.
• Switch off the power supply and pull out the mains plug.
• Remove everything from the desk top which might contribute weight.
5. Before start-up:
• Make sure that the power supply is between 110v and 240v before plugging the
• The individual parts must be connected before the control box is connected to
6. During operation:
• If the control box makes unusual noises or smells, switch off the main power
• Take care that the cables are not damaged.
• Unplug the main power cable on mobile equipment before it is moved.
memory controller. There is a risk of injury and electric shock.
physical or mental abilities can’t use the product.Unless they are under
surveillance or they have been thoroughly instructed in the use of the apparatus.
control box into it.
the main power supply.
immediately.
There is a risk of injury and electric shock.
20
16/
1. Reset Procedure
Digital Memory Controller
You can use this function to adjust the desktop to a saved height with 4 posi-
tions. If you are switching on the control unit for the first time, all the saved
position are set to the lowest desktop height, to change to a saved position
proceed as follows:
a. Press the UP or DOWN key to adjust the desktop to the desired
2. Storing a Position
height, the display will show the desktop height.
and " " at the same time until the desk reaches its lowest height, and
the system will make a sound of beep, reset is complete.
a. Press the " " and " " at the same time for 3 seconds , until the display
shows "RES", and the system will make a sound beep , reset is complete.
b. If the Position of desktop is not at the lowest height. Please press the " "
IMPORTANT: You must reset the desk prior the use.
Make sure no obstacles are in the desk’s path.
Make sure the desktop is not touching any walls.
Make sure all cords are appropriate length to accommodate the change in height.
20
17/
• To program up to four presets : Use the up/down buttons to find a desired
CAUTION: Once a preset button is pushed, the desk will move to the
programmed height.
The height unit can be switched between CM and Inch, check the proceed as
follows:
a. Press the " " and " " at the same time for 3 seconds.
b. Display started flashing and read "C-E".
c. Press the " " within 10 seconds, the display show "C", and switched the
d. The display stopped flashing, and the switch is complete.
3. Switch the unit between CM and Inch
unit to CM; Pressthe " ", the display show "E", and switched the unit
to "inch".
height, then press "M" followed by a number 1 - 4.
Press the DOWN button on the memory controller until the frame reaches its
lowest position. Measure the height of the frame from the floor and if the number
on the LED display does not match your measurement, follow these steps:
4. SETTING THE LED RETRACTED HEIGHT
b. Press and hold the "M" Key for 3s until the numbers on the display
started flashing.
• The other position may be stored in the same way.
• The desk base can be adjusted by pressing and holding either the UP or
c. Press memory position Key 1 to save the desk position in memory.
d. The display will read "P 1" the memory position number you saved.
DOWN button until the desired height is reached.
AC2-AA3_English V01拼 自翻版