background image

TM

P

P ii ee zz oo // M

M aa gg nn ee tt ii cc   

P

P ii ee zz oo // M

M aa gg nn ee tt ii cc   

O

O nn bb oo aa rr dd    M

M ii xx ii nn gg    P

P rr ee aa m

m pp

O

O nn bb oo aa rr dd    M

M ii xx ii nn gg    P

P rr ee aa m

m pp

Thank you for purchasing this Fishman Powerbridge accessory. We are con-
fident that the Powerchip will significantly enhance the performance of your
Powerbridge system. If you have any questions or comments, please con-
tact our Customer Service Line at 978-988-9665.

Warning

Installation of the Powerchip may require structural modification to the gui-
tar. We strongly recommend that any modifications be performed by a com-
petent repair person. Fishman Transducers will be in no way responsible for
damages to the guitar, incurred as a result of improper  installation.

Description and Features

The Powerchip is a miniature onboard Piezo/Magnetic pickup mixing pre-
amp, dedicated to the Fishman Powerbridge system. The preamp, mounted
to the underside of a volume pot, allows guitarists to combine or split Piezo
and Magnetic pickups without any additional outboard signal routing elec-
tronics.

The Powerchip features an independent Piezo volume control, and internal
“set it and forget it” Phase and Piezo Trim controls. A “smart” electronic
switch in the Powerchip circuit automatically routes Piezo and Magnetic
pickup signals to either stereo or mono signal paths.

Powerchip

2

Summary of Contents for POWERCHIP













Reviews: