Fisher-Rosemount Posi-Seal A31 Instruction Manual Download Page 1

D500240X012

Posi-Seal

R

 Type A31A High Performance 

Butterfly Valve 3 through 12-Inch

Contents

Introduction

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Scope of Manual

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Specifications

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Description

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Installation

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Adjusting the Actuator Travel Stops or Travel

3

. . . . 

Valve Orientation

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Preparing for Installation

4

. . . . . . . . . . . . . . . . . . . . . . 

Installing Wafer-Style Valves

7

. . . . . . . . . . . . . . . . . . . 

Installing Single-Flange Valves

8

. . . . . . . . . . . . . . . . . 

Maintenance

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Replacing Packing

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

Removing the Valve from the Pipeline

10

. . . . . . . . . 

Removing/Installing the Seal Ring

11

. . . . . . . . . . . . 

PTFE Seal Installation

11

. . . . . . . . . . . . . . . . . . . . . 

NOVEX Seal and Phoenix III
Fire-Tested Seal Installation

12

. . . . . . . . . . . . . . . . 

Cryogenic Seal Installation

13

. . . . . . . . . . . . . . . . . 

Anti-Blowout Protection, Packing,

Valve Shaft(s), Disk, and Bearing
Maintenance

14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Removal

14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Installing a One-Piece Shaft

16

. . . . . . . . . . . . . . . . 

Installing a Two-Piece Shaft

16

. . . . . . . . . . . . . . . . 

Installing the Gasket Retainer

17

. . . . . . . . . . . . . . . 

Parts Ordering

18

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

Parts Reference

18

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

Introduction

Scope of Manual

This instruction manual provides installation, mainte-
nance, and parts ordering information for the 
POSI-SEAL Type A31A high-performance butterfly

Figure 1. Typical Type A31A Valve

W5812-1/IL

W5811-1/IL

valves. Figure 1 shows typical Type A31A valves. For
information regarding actuators and accessories, refer
to separate instruction manuals.

Only personnel qualified through training or experience
should install, operate, and maintain this valve. If you
have any questions concerning these instructions,
contact your Fisher Controls sales representative or
sales office before proceeding.

Description

The Type A31A high-performance butterfly valve fea-
tures a keyed drive shaft. The keyed shaft combines
with a variety of handlevers, handwheels, pneumatic
piston or spring-and-diaphragm actuators to make the
Type A31A a reliable, high-performance, butterfly
valve for a variety of applications in the various pro-
cess industries.

Instruction Manual
Form 5456
November 1998

Type A31A

Summary of Contents for Posi-Seal A31





















Reviews: