manualshive.com logo in svg

Fisher & Paykel CLEANSMART WL8O60P, Installation Manual

Share
Download
Fisher & Paykel CLEANSMART WL8O60P Installation Manual Download Page 6

INSTALLATION INSTRUCTIONS

6

INSTALLATION INSTRUCTIONS

Accessories

Check if you received the following accessories with your Fisher & Paykel washer. You will 
find them inside the drum or attached to the packaging.

 

z

2 x inlet hose(s)

 

z

1 x hose guide

1 

Remove the outer packaging.

2 

Tilt the washer backwards and walk it off the base 
packer one foot at a time (ensure the lid is still 
taped down).

3 

Remove the base packer from under the washer by 
tilting the washer backwards and pulling the packer 
out the front.

4 

Remove the tape, lift the lid and remove the bowl 
packer from the bowl. 

5 

Remove the hoses and accessories. 

6 

Keep the base packer and bowl packer in case they 
are required for future transit.

Removing the packaging

Unpacking

To ensure the best performance from your new washer please follow the instructions below.

Please ensure that the base packer has been removed before operating your machine.

Summary of Contents for CLEANSMART WL8O60P





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands