Use
Helmet fitting
You will only ensure optimal protection if your helmet fits just right.
The helmet must not rest on the back of your head, but should not
be pulled too low on your forehead either and must
not be shifted to the left or right.
Adjusting the helmet on the inside
This helmet features a new, patented fitting ring with a rotary mech-
anism. The size can easily be set with one hand.
• Place the helmet level on your head with the fitting ring open. The
bottom edge of the helmet must rest 1-2 finger-widths above the
top of your nose.
• If the helmet can easily be moved, the fitting
ring (1) must be set tighter. You do this using
the rotary knob (2). Turning it clockwise
makes the circumference of the fitting ring
smaller, turning it anti-clockwise make it big-
ger.
• Tighten the fitting ring until it fully encircles your head and does
not become loose.
Adjusting the straps
In case of a fall, the helmet only protects
your head optimally if the straps are correctly
adjusted.
• Place the two Y-shaped strap holders (3)
approx. 1 cm below your ears. The straps at
the back go round the back of your head at
this point.
• Fasten the strap buckle underneath your
chin (Fig. 4). The chinstrap must be pulled
taut but not too tight. You should be able
to still open your mouth slightly when the
buckle is fastened. The correct position for
the fastened chinstrap is underneath the
lower jaw, between the point of your chin
and your throat.
WARNING:
Always wear the helmet with the
chinstrap fastened.
• If any of the straps are
too long or too short,
these can be adjusted
simply by pulling them.
• If the helmet does not
fit the size of your head
after all, you should
choose another size or
another helmet.
Illuminated ring system
The illuminated ring system is switched on by pressing the white
LED cover.
Function:
• Flashing light • Constant light • Off
Changing the battery
Carefully remove the white cover from the light. Now you can
replace the dead battery with a new one. Carefully press the cover
back on to the black adjustment dial.
• Note the polarity of the batteries. Battery type: button cell 2x 1,5V
LR 41.
• Do not use rechargeable batteries.
• Remove leaking batteries immediately. When doing so, avoid con-
tact with the skin. In the event of contact with the skin, thoroughly
clean the areas affected with water.
• LED class 1: There is no hazard from the light if used correctly.
• After use the batteries may be handed over free of charge
at authorised battery collection points. The end user is legally
obliged to return the batteries to an authorised collection point.
ATTENTION:
Please bear in mind that the illuminated ring system
is only an additional form of lighting. This does not replace lighting
according to the Road Traffic Licensing Regulations.
Cleaning
Use only water, mild soap and a soft cloth for cleaning your
helmet. Do not use solvents like spirit or petrol. Solvents may attack
the helmet skin. The internal pads are washable at 30°.
Disposal
The packaging and ancillary packing consist entirely of environ-
mentally-friendly materials. They can be disposed of at your local
recycling facility.
Contact your local refuse disposal authority for more details
of how to dispose of your worn out product.
Disposal of batteries
Used batteries must not in any event be put in the domestic
refuse. Hand these in to your dealer or your public collection point
for recycling.
Informationes
Guarantee
With this product you receive a guarantee that is valid from the date
of purchase.
In the event of a fault in its functions occurring during the guarantee
period, please send the helmet to the listed service address making
reference to the following model number: FZ-016.
Spare parts such as internal pads and strap clasps can be ordered
at the service address below.
Service:
MTS Group
MTS MarkenTechnikService GmbH & Co. KG
Carl-Benz-Straße 2 · 76761 Rülzheim · Germany
www.mts-gruppe.com
Declaration of conformity
*
* The product satisfies the regulation on personal protective equip-
ment (EU) 2016/425.
Tested in accordance with EN 1078:2012+A1
** The declaration of conformity can be viewed via the following
link: http://iuqr.de/FZ024
Address of the notification body:
TÜV Rheinland LGA Products GmbH
Tillystraße 2 · D-90431 Nürnberg
Notified Body 0197
Status 04/20
3
Press
Press
4
Fastener
Winding
Chinstrap
1
2
