Fireye SureFire HESI Page 12 Instruction Manual Download

Page: 12 / 16

ORDERING INFORMATION: FIXED MOUNT HESI IGNITER

FIXED MOUNT HESI IGNITER SPECIFICATION STEPS (Refer to figure 2)

Select the appropriate HESI Power Pack (P/N SF1-X).

Select the appropriate HESI Interconnecting Cable (P/N SF1-CA1-XX).

Select the appropriate HESI Rod, (P/N SFR-XXX), taking note of the 12” minimum external
length.

Select the appropriate optional

fixed

mounting tube (P/N MT1-XXX).

SELECT THE APPROPRIATE HESI POWER PACK

PART NUMBER

DESCRIPTION

SF1-1

SureFire HESI Power Pack, 110 vac, NEMA 4 (painted steel)

SF1-2

SureFire HESI Power Pack, 220 vac, NEMA 4 (painted steel)

SF1-3

SureFire HESI Power Pack, 110 vac, NEMA 4X (stainless steel)

SF1-4

SureFire HESI Power Pack, 220 vac, NEMA 4X (stainless steel)

SELECT THE APPROPRIATE HESI INTERCONNECTING CABLE

PART NUMBER

DESCRIPTION

SF1-CA1-06

SureFire HESI interconnecting cable with connectors, 6 feet long

SF1-CA1-09

SureFire HESI interconnecting cable with connectors, 9 feet long

SF1-CA1-12

SureFire HESI interconnecting cable with connectors, 12 feet long

SF1-CA1-15

SureFire HESI interconnecting cable with connectors, 15 feet long

SF1-CA1-20

SureFire HESI interconnecting cable with connectors, 20 feet long

SF1-CA1-25

SureFire HESI interconnecting cable with connectors, 25 feet long

SF1-CA1-50

SureFire HESI interconnecting cable with connectors, 50 feet long

Summary of Contents for SureFire HESI

















Search results

Summary of Contents for SureFire HESI

Reviews:

Related manuals for SureFire HESI

Brands by name

Popular brands

Fireye SureFire HESI, Instruction Manual

Search results

Summary of Contents for SureFire HESI

Reviews:

Related manuals for SureFire HESI

Brands by name

Popular brands