manualshive.com logo in svg

Firemiks 1200-3-PP-F-ALU-FM, Instruction Manual

Share
Download
Firemiks 1200-3-PP-F-ALU-FM Instruction Manual Download Page 22

Page 22/43 

 
 
 
 

 

 

 

 

Firemiks AB 

Instruction manual version: SPFA FM 

P.O. Box 8155, 104 20 STOCKHOLM, Sweden 

  

phone +46-8-551 196 10 - [email protected] - www.firemiks.com 

4.7.5  Filter 

The flushing line is equipped with a filter so that no debris may enter 
the pump during flushing. There are two types of filters used on a 
Firemiks, check which type your Firemiks is equipped with and learn 
how to clean it.  

4.7.5.1  Traditional Y-strainer 

 

On this filter type, the system must be made pressure free before 
opening the filter cap. This filter type is standard issue on all units 
covered in this instruction manual.  

 

4.7.5.2  Ball valve with integrated filter (only available on special request) 

 

With this filter type, there is no need to make the system pressure 
free to open the filter. The filter can be cleaned with pressure in the 
system by closing the valve (handle is put perpendicular to the pipe, 
in the ‘OFF’ position) and opening the filter cap.  

 

WARNING!: Only close the filter valve for cleaning the filter. In 
all other circumstances, be sure this valve is always OPEN 
(handle parallel to the 

pipe, in the ‘ON’ position)! Otherwise 

during operation no flushing can be done and the pump will run 
dry if attempting to flush the system.  

 

 

Summary of Contents for 1200-3-PP-F-ALU-FM












































Reviews:

No comments

Brands by name

Popular brands

Load more brands