manualshive.com logo in svg

Firegear KWBH-2, Owners & Installation Manual, Page: 17 / 40

Share
Download
Firegear KWBH-2 Owners & Installation Manual Download Page 17

Firegear Outdoors® Key West™ Series

17

INSTALLATION

LP HARD LINE CONVERSION

(FOR USE IN PLACE OF LP TANK)

 

Each Kit contains one LP Hard Line Conversion Kit  
Conversion Kit Contains:
Qty. Part 

# 

Description

 1         909-265    Max 0.5 psi label
 1         286-035    Regulator mounting base
 1         286-036    Regulator mounting top
 1         911-136    Regulator LP
 1         904-978    3/8” fl ex pipe 18”  length
 4         904-959    #8 Philips 
 1    

919-343   Instruction sheet

Turn off unit and allow to cool to room temperature

.

1

.  Remove gas knob by pulling off - then remove end panel by lifting up 

and off.

Diagram 1

Diagram 2

5.

 Remove LP hose from valve.

LP hose

Diagram 3

Diagram 4

Diagram 5

2

.  Remove panel on opposite end by lifting up and off.

3

. Disconnect and remove LP tank.

4

. Remove 3 screws in locations shown below to remove side panel.

Note

: Coffee height table requires removal of only 2 screws (no middle 

screw).

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION !!

Summary of Contents for KWBH-2









































Reviews:

No comments