background image

INSTALLATION UNDER COOKER HOOD

6

P. 6-7

STARTING THE HEAT 
SENSOR

Insert the battery and check step 4 
before placing the Heat Sensor on the 
installation plate.

Briefly press the button. The 
LED should flash green.

CHECK INSTALLATION HEIGHT

If the distance from cooker to Heat Sensor is more than 60 cm, the Heat 
Sensor's sensitivity level must be adjusted manually.

Please refer to the table below together with the information on page 16. 

Also watch the video on sensitivity configuration below.

3

* The installation may not in all cases meet all EN standard requirements. 
See FAQ, page 18, point 4

Please note: the sensitivity level of the Heat Sensor is 

confirmed by the appropriate sound pattern sequence 

only (not LED flashes).

Watch the film:

https://youtu.be/oy-hrT7nTQM

Setting the sensitivity level

4

Watch the film:

https://youtu.be/SAeFdB3nP3s

Installation

DISTANCE FROM 

COOKER TO

 

HEAT SENSOR

MOUNTING LOCATION

SENSITIVITY LEVEL CONFIGURATION

0–60 cm 

wide cooker

61–90 cm

wide cooker

Sensitivity

Acknowledgement "beep(s)"

81–100 cm

Zone 1 & Zone 2

Zone 1

3 presses

   

76–80 cm

Zone 1
 
Zone 2

*

Zone 1

*

 

4 presses

     

71–75 cm

5 presses

       

65–70 cm

6 presses

         

61–64 cm

7 presses

             

45–60 cm 

   

Factory setting

8 presses

             

Summary of Contents for Stove Guard FSG 1

























Reviews:

Related manuals for Stove Guard FSG 1