background image

   INSTALLATION        5

1a

15cm

Zone 2

Zone 1

Radius 15 cm

Min 10 cm

Min 5 cm for

LED lamp

Zone 1 is immediately 
above the middle of the 
cooker plates. Max 15 cm 
from the centre.

Zone 

1

COOKER HOOD

Measure the installation height. The Heat Sensor should 
be centred above the cooker, preferably within Zone 1 
(see diagram at bottom of the page).  It can be attached 

to the grease filter. It is also important to ensure the 

minimum distance from any lights underneath the hood 
is 10 cm (5 cm is enough for LED lamp). 

Please note: Zone 1 is recommended for best 
performance.

1

Measure distance

SELECTING THE MOUNTING LOCATION

I

f there is a metal mesh grease filter on the cooker hood, 

make sure it is free of grease and dry. 

Carefully remove the protective film from the installation 

plate.  Press for at least a minute while attaching installation 
plate to allow adhesive to work.

2

MOUNTING THE INSTALLATION PLATE

Allow the Heat Sensor to reach room temperature before use.  
The power to the cooker must be switched off (at the consumer unit).  
See table on page 6 for the mounting location and follow instructions 1–4.

Summary of Contents for Stove Guard FSG 1

























Reviews: