background image

Page 1 

 

www.fimcoindustries.com 

1000 FIMCO Lane, P.O. Box 1700, North Sioux City, SD  57049      

Toll Free Phone: 800-831-0027 : Toll Free Fax: 800-494-0440 

[5004598   

 

 

 

 

 

(11/20)] 

Model: LG-60-3PT-BL 

(5301340) 

(60 Gallon 3 Point Sprayer 

w/3-Nozzle ’Boomless’ Boom Assembly)

 

Information About the Sprayer 

Roller pumps are positive displacement pumps, which means 

that the entire solution being pumped must go somewhere or 

the pump will break. In this roller pumping system, solution is 

drawn from the tank and forced to a planned source, such as 

boom  nozzles  or  handgun.  The  pressure  is  controlled  by  a 

pressure  relief  valve,  which  is  a  spring-loaded  device  that 

controls  the  amount  of  fluid  bypassed  (recirculated)  to  the 

tank. The gray adjusting cap is to be tightened to  

increase pressure and loosened to decrease pressure. 

The ‘directo-valve’ is the on/off control which allows the  

operator to manually control the solution going to the boom. 

 

Assembly Instructions 

Most of the sprayer has been assembled at the factory. 

 

Center  the  boom  tube  on  the  boom  mounts  and  secure  in 

place with the (2) round U-bolts and whiz nuts provided. 

Make  sure  the  U-bolts  are  positioned  within  the  grooves  of 

the grommets on the boom tube. Refer to page 2 to attach  

the end nozzles to the boom. 

 

NOTE: The purpose of these grommets is to prevent met-

al-to-metal contact between the U-bolts, boom tube and 

boom mounting brackets. 

 

The grommets will ‘compress’ as you tighten the whiz lock-

nuts onto the U-bolts. Tighten just so that the boom tube will 

NOT rotate within the grommets. Alternate the tightening of 

the locknuts to provide even pressure on the grommet. 

**DO NOT OVER TIGHTEN the whiz locknuts, as this may 

cause the boom tube to flatten slightly! 

 

Attach  the  boom  feeder  hose  to  the  boom  after  routing  it 

through the underside of the carrier frame as needed. Secure 

in place with a hose clamp provided. 

 

Poly hose fittings (5010209) are included to be joined to the 

pump. A torque chain, ‘S’-Hook and hardware are also includ-

ed for the pump. The pump IS NOT included with this unit. It 

is  intended  for  a  pump  to  be  mounted  directly  to  the  tractor 

PTO. 

Category I

 

Caution:  When  fully  filled  with  water,  this  sprayer  will 

weigh  approx.  700  lbs..  Consult  the  owner’s  manual  for 

your vehicle to verify that  you are within it’s load carry-

ing capacity.  

OWNER’S MANUAL

 

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON, PLEASE CALL

1-800-831-0027

MONDAY-FRIDAY, 8:00 AM TO 5:00 PM CST

If you should have a question or experience a problem with

your Fimco Industries Product: Visit our website @ 

www.fimcoindustries.com or call the Toll free number above. Our 

technical support representatives will be happy to help you. 

In most cases a customer service rep. can resolve

the problem over the phone.

To obtain prompt, efficient service, always remember to give the 

following information....

• Correct Part Description and/or part number

• Model number and Serial Number

Part descriptions and numbers can be obtained from the

illustrated parts list section(s) of this manual.

General Information 

Thank you for purchasing this product. The purpose of this 

manual is to assist you in operating and maintaining your 

3-Point sprayer 

Retain a copy of your receipt for your unit, as it will be required 

to validate any warranty service. 

 

Warranted against manufacturer or workmanship defects from 

date of purchase with copy of receipt: 

 

Homeowner Usage: One Year. 

 

Commercial Usage: 90 Days.

 

Summary of Contents for LG-60-3PT-BL









Reviews: