Fike ECS Series Installation & Operation Manual Download

Page: 46 / 66

ECS Series Manual —

P/N LS10262-001FK-E:A 3/3/2021

Device Installation

Installing the FIK-DUAL50W

Batteries larger than 18 AH will not fit in the main control cabinet, and must be housed in the RBB Accessory Battery Cabinet. Maximum of
35 amp hr for the system.

4.7 Installing the FIK-DUAL50W

/HV

This section provides information on how to install the FIK-DUAL50W for use with the FCP-300ECS and FCP-2100ECS.

The

FIK-DUAL50W is available with 240VAC input as FIK-DUAL50WHV.

Device

No. of

Devices

Current Per Device

Standby

Current

Alarm

Current

FIK-125W 120V

Standby:

375 mA

375mA

Alarm:

700 mA

700mA

FIK-125W 240V

Standby:

Alarm:

FIK-CE4

0 or 1

Standby:

20 mA

20mA

Alarm (All Channels): 180 mA

180mA

Current Subtotals:

Notification Devices

Refer to device manual for number of devices and current ratings.

Current Subtotals:

Total current rating of all devices in system (Line B) X 0.001

Number of standby hours (24 or 60 for NFPA 72)

Multiply line C (standby current) and D:

Total standby AH

Alarm sounding period in hours (For example, 5 minutes = 0.0833 hours):

Multiply line C (alarm current) and F:

Total alarm AH

Add lines E and G (AH = Ampere Hours):

Total AH required

Table 4.4 Current Draw FIK-125W

Summary of Contents for ECS Series



































































Search results

Summary of Contents for ECS Series

Reviews:

Related manuals for ECS Series

Brands by name

Popular brands

Fike ECS Series, Installation & Operation Manual

Search results

Summary of Contents for ECS Series

Reviews:

Related manuals for ECS Series

Brands by name

Popular brands