Fiery X2 Administrator'S Manual Download Page 59 | Manualshive

Page: 59 / 164

Fiery X2 Administrator'S Manual Download Page 59

2

2-23

Network Setup options

Server Name
Default Name

The server name is the name that will appear on the network for accessing the Fiery X2
via SMB. The default name is the same as the server name assigned in Server Setup (see
page 2–8).

Server Comments

Server comments (optional) can contain information about the printer.

Workgroup or Domain

Enter the workgroup or domain you want the Fiery X2 to appear in.

Web Services Setup

N

OTE

:

You must publish the Print queue to use the Fiery WebTools (see page 2-36).

Network Setup

Service Setup

Web Services Setup

Enable Web Services
Yes/No [No]

Select

Yes

if TCP/IP is enabled on the Fiery X2 and on user workstations, and you

wish to make the Fiery WebTools available to users (see page 4–25). The
Fiery WebTools include Fiery WebSpooler, Status, WebLink, and Installer. A Java-
enabled Web browser and a valid IP address are required for each user. See Getting
Started for details on browser choice and workstation requirements.

«
...
57
58
59
60
61
...
»

Summary of Contents for X2





































































































































































Reviews:

No comments