Fiery X2 Administrator'S Manual Download Page 52 | Manualshive

Page: 52 / 164

background image

2

2-16

Setting up the Fiery X2

TCP/IP Setup options

TCP/IP Setup with Ethernet

To configure the Fiery X2 for TCP/IP, choose TCP/IP Setup.

Choose Ethernet Setup and enter the appropriate settings. Choose each network
type you use (Ethernet and/or Token Ring) and enter the appropriate settings.
Token Ring Setup appears as an option only if you have enabled Token Ring in Port
Setup. If your network uses a gateway, enter the gateway address in Gateway Setup.

N

OTE

:

If TCP/IP is running on both an Ethernet and a Token Ring network, it is

assumed that the two networks are already routed to each other. The Fiery X2 does
not function as a router.

Network Setup

Protocol Setup

TCP/IP Setup

Ethernet Setup

Enable TCP/IP for Ethernet
Yes/No [No]

Select

Yes

if you have a TCP/IP network connected to the Fiery X2 over Ethernet

cabling.

If you use Token Ring, enabling TCP/IP for Token Ring is required for enabling the
Fiery WebTools.

N

OTE

:

If you are using TCP/IP for printing from Windows NT 4.0 workstations,

enabling TCP/IP here also enables you to use the Fiery utilities from
Windows NT 4.0 workstations using TCP/IP protocols. At the same time, enabling
TCP/IP enables the network layer that lets you use the Fiery utilities from
Windows 95 computers using IPX/SPX protocols.

Exit Protocol Setup
AppleTalk Setup
TCP/IP Setup
IPX/SPX Setup

Protocol Setup

Exit TCP/IP Setup
Ethernet Setup
Token Ring Setup
Gateway Setup

TCP/IP Setup

«
...
50
51
52
53
54
...
»

Summary of Contents for X2





































































































































































Reviews:

No comments

Related manuals for X2

SuperServer E100-8Q

Brand: Supermicro Pages: 48

Brand: YOKOGAWA Pages: 22

FusionServer 2288 V5

Brand: xFusion Digital Technologies Pages: 86

Brand: Protogate Pages: 30

Brand: Ekselans Pages: 37

Brand: QNAP Pages: 58

Brand: Supero Pages: 112

Brand: Sony Pages: 8

BSV-M1 - StorStation NAS Server

Brand: Sony Pages: 58

Brand: EVS Pages: 126

Brand: Bosanova Pages: 2

G4-Apex-ENT-80T

Brand: Viavi Pages: 11

Brand: Black Box Pages: 48

Brand: Advantech Pages: 110

Brand: 3onedata Pages: 3

Brand: 3onedata Pages: 20

SUPERO SUPERSERVER 5015B-MT

Brand: Supero Pages: 106

Brand: NASdeluxe Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands