Fiery X2 Administrator'S Manual Download Page 27

Page: 27 / 164

1-7

Fiery X2 on the network

Windows NT 4.0 Server environment

Windows computer

Key to setup:

1 Windows NT 4.0 Server

page 4-19

2 Fiery X2 Setup

Chapter 2

3 Windows NT 4.0 client

page 4-23

TCP/IP

Another supported
protocol

LAN with
NETBEUI, etc.

Printing on this network

Windows 3.1x and Windows 95 clients can
print using a protocol available on the
Windows NT 4.0 print server
Windows NT 4.0 machines can print using
TCP/IP with the lpd protocol

For running Fiery utilities and WebTools

A Windows NT 4.0 computer with TCP/IP
loaded

NETBEUI or other protocol available on
the clients and the server

TCP/IP (lpd) for printing
TCP/IP (http) for Fiery WebTools
TCP/IP for Fiery utilities

Windows NT 4.0 computer
with TCP/IP loaded

Windows NT Workstation
or Windows NT Server
acting as print server

Fiery X2 connected to copier

Summary of Contents for X2





































































































































































Search results

Summary of Contents for X2

Reviews:

Related manuals for X2

Brands by name

Popular brands

Fiery X2, Administrator'S Manual

Search results

Summary of Contents for X2

Reviews:

Related manuals for X2

Brands by name

Popular brands