manualshive.com logo in svg

Fidelity Electronics C-10 Series, Operation Manual

Share
Download
Fidelity Electronics C-10 Series Operation Manual Download Page 29

29 

8.4 Android and iOS APP 

Android and iOS App are available to work with this instrument: -  

•

 

For Android App: - Visit Google Play and search for aConnect.  

•

 

For iOS App: - Visit Apple App Store and search for FMDirect. 

 
These Apps support both Bluetooth and WIFI connection. 
 

8.4.1 Settings when Using App via WIFI Connection 

1. 

Make sure that the optional built-in WIFI or LAN module is ordered.  

2. 

Set  UART  #3  of  internal  function  F16  to  WIFI  or  LAN  depends  on  the  options  ordered.  Then  set 
transmission type to CMD. 

3. 

Make sure that the weighing instrument and your smart device is under the same Network / SSID.  

4. 

Enter the IP and port number of the built-in WIFI / LAN module on the starting page of the APP.  

5. 

Once the IP and port numbers are entered, APP starts. 
 

Contact your dealer for support / more setting information about built-in WIFI / LAN module. 

 
8.4.2 Settings when Using App via Bluetooth Connection 

1. 

Make sure that the optional built-in Bluetooth module is ordered.  

2. 

UART #2 of internal function F16 should be either set to BT. Then set transmission type should be set 
to CMD. 

3. 

Bluetooth Type of internal function F50: -   

•

 

For Android, set to BT2.0. Then set Bluetooth working type to Andro.  

•

 

For iOS, set to BT4.0. Then set Bluetooth working type to iOS.  

4. 

Then change or take note of the BT device name and pin number 

5. 

Pair your smart device with the built-in BT2.0 module before starting the APP.  

6. 

Start APP, and select the correct Bluetooth device on the starting page of the APP.  

7. 

Once the correct Bluetooth name is selected, APP starts. 

 
Contact your dealer for support / more setting information about built-in Bluetooth module. 
 

 

9. Basic Operation 

9.1 Power Instrument On and Off 

•

 

To power on: - press 

[On/Off] 

and then release. 

•

 

To power off: - press 

[On/Off] 

and then release. 

 

9.2 Power on Countdown Process 

After powered on, instrument goes through the power on countdown process and display the below information. 

1.  Software number (LCD1) and version (LCD2). 

2.  All display segments. 

3.  Calibration count value (LCD2), parameter set count value (LCD3) and Battery voltage  (LCD1). 

4.  Capacity & division set of P1 (LCD1) in the format of Max plus 1 division (LCD2 = Max

1

 + e

1

); (LCD2 

= Max

2

 +d

2

). 

5.  Capacity & division set of P2 (LCD1) in the format of Max plus 1 division (LCD2 = Max

1

 + e

1

); (LCD2 

= Max

2

 +d

2

). 

Summary of Contents for C-10 Series
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands