Fidelity Electronics A10 Operation Manual Download Page 52

Page: 52 / 98

Err 64

The number of files in the folder path exceeds 20

--oL--

Overload (Gross weight is more than Max plus 9d)

HALT

Major system error detected. Power off instrument and remove power adaptor
immediately. Then check load cell connection and system power status.

UndEr

Negative Weight value exceeds display range

Reboot

Important parameters have been changed. Power off and then power on instrument
again to reboot.

------

Negative Tare value exceeds display range

25. Daily Care & Maintenance

Clean this instrument with a soft, damp cloth. If necessary, use a mild detergent in water.

Do not use any harsh, abrasive material, acetone, volatile solvent, thinner, or alcohol for cleaning.

Verify the accuracy of this instrument periodically. Re-calibrate if necessary. In some countries,
calibration requires an authorized/qualified agent. Contact your dealer for more information.

Store this instrument in a dry and clean place.

Recharge battery before and every 4 months during long time storage.

Summary of Contents for A10



































































































Search results

Summary of Contents for A10

Reviews:

Related manuals for A10

Brands by name

Popular brands

Fidelity Electronics A10, Operation Manual

Search results

Summary of Contents for A10

Reviews:

Related manuals for A10

Brands by name

Popular brands